Question about Maytag MER5770 Electric Kitchen Range

1 Answer


Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: ERROR MESSAGE - Maytag MER5770 Electric Kitchen Range Kitchen Ranges

F1 appears on panel

Posted on Jun 03, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Error message on Whirlpool Range Oven Model GFE461LVS Feature Not Available

The Feature not available message indicates that the range's internal computer (electronic control) has found a problem with the range. You need to access the diagnostic program to determine the fault and try to reset it. Press Cancel, Cancel (a second time) and then Start. You should see Test On. Then press Temp > Time > + . Press + again to move through the various test and information sections. Eventually you should get a list of Faults (F followed by a number or F number E number). Record these. After you press + again, the diagnostic program should enter an "Auto Test". Press Cancel to exit the test. Then press Start Time to clear the fault codes. Then try to use your oven.

Some faults mean that the oven can't be used until you fix the problem. These can be problems with the ERC (electronic range control), high temperature limit sensor, or wiring harness. Some of the parts for your range are available here: . Without the error code, I can't pin down your issue. So please add a comment with that information after you try the diagnostic.

If your range is under warranty, contact Whirlpool for a service call.

I hope this helps.

Cindy Wells

May 10, 2016 | Whirlpool GFE461LV Electric Range

1 Answer

F1e2 error code

F1E2 error code usually refers to something with the control board. I do not have info before me, but believe the board has to be replaced.
Package info somewhere inside your stove will give you the explanation of that error code.

It does not hurt to unplug the stove for fifteen minutes/turn it on again and see what the error code is, if any.

Oct 19, 2013 | Whirlpool SF367 Gas Kitchen Range

1 Answer

What does error code f1e2 mean and how to fix it

Problem with the board. First try tightening up the harnesses on the board; make sure the buttons are not stuck, turn oven off and on again and see what the code reads..if any.
Do not have exact explanation for error code but know that that is where your problem lies.

Oct 19, 2013 | Kitchen Ranges

1 Answer


Hello parmantal - Typically error code F31 indicates that the unit has a shorted probe connection problem. Try resetting the range by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and this will usually clear most false codes. If it proves to be ineffective, contact a professional to move forward accurately. The technician will need to check the resistance and/or harness between the EOC and probe connector. Depending on the diagnoses part(s) will need replacing.

Dec 18, 2012 | Frigidaire FEF352 Electric Kitchen Range

1 Answer

I put the oven on to preheat and it started beeping. I'm getting an error message of F 3 then the oven shuts off The range is 17 years old and I don't have the manual.

F3 error means the issue is with the oven temp. sensor that is bad and you need to replace it. You can test the oven temp. sensor for 1100 ohms and if the reading is more then 1100 then it should be replaced, else it is the ERC (range control) that should be replaced. Hope this helps...please post back for further assistance.


Jan 19, 2011 | Kitchen Ranges

1 Answer

Error F1E2 Whirlpool Super Cap Gas Range 465, oven crazy!

F1 E2

1. Verify failure if not displayed, using CANCEL/OFF key. Press key for 5 seconds until last
error code is displayed.
2. Disconnect power longer than 30 seconds.
3. Re-apply power and observe for longer than 1 minute.
4. If failure remains, disconnect power, replace control.

Nov 22, 2008 | Whirlpool GS460 Gas Kitchen Range

2 Answers

Whirlpool oven

if you get down to the control panel first try plug and unplugging all the connectors as resistance can cause this in the connectors next take the Mylar ribbon off the control and clean it softly with a pencil eraser as the touch pad malfunction can cause now if you have an ohm meter you can ohm the oven probe it should be 1200 ohms at 70 degrees room tempture if all this fails to fix it then replace the controls bd ive seen too many techs too quick to replace a 200.00 control board just because the eoc spouts out an error code

Jan 28, 2008 | Whirlpool SF367 Gas Kitchen Range

1 Answer

Error code F1E2

The code F1E2 refers to a watchdog circuit in the ERC (Electronic Control Card). This can only be corrected by replacement.

Dec 29, 2007 | KitchenAid KESC300 Electric Kitchen Range

1 Answer

Whirlpool Gas Oven

The F1, E2 codes mean you have UL ac-dc errors. This means you need to replace the control.

Dec 21, 2007 | Whirlpool SF367 Gas Kitchen Range

Not finding what you are looking for?
Maytag MER5770 Electric Kitchen Range Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Kitchen Ranges Experts


Level 2 Expert

283 Answers


Level 3 Expert

2963 Answers


Level 2 Expert

236 Answers

Are you a Maytag Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides