Question about Epson Stylus CX4600 All-In-One InkJet Printer

2 Answers

My Epson CX 4600

After moving my printer to a new location and reconnecting it to my computer, I turned it on and all it does is flash all it's lights. I can't get it to print any thing. Any suggestions?

Posted by on

2 Answers

Re: My Epson CX 4600 - Epson Stylus CX4600 All-In-One InkJet Printer Printers & Copiers

After moving my comep

Posted on Jan 13, 2008

Re: My Epson CX 4600 - Epson Stylus CX4600 All-In-One InkJet Printer Printers & Copiers

Use a big hammer

Posted on Jan 13, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Hello. My Epson Stylus CX 4200 now flashes the letter E and all the lights flash, including "error." How do I get it working again?

here's what you can do:-disconnect the printer from the computer-turn off the printer-inspect for anything foreign inside like jammed paper-turn the power back on-remove the ink cartridge-check the chip connnector at ink tank and at head carriage. If its dirty clean it with soft moist cloth. -check the status monitor. which ink tank not recognized. -press ink light (1-4 times) depends on number ink tank not recognized, press 1 time again, carriage will move co replacement position, unplug and plug again all ink tank, press ink light 1 more.
if that doesn't work, replace ink cartridge ONLY if you have a spare. DO NOT BUY new ink as the printer is bound for repair.

Nov 13, 2011 | Epson Stylus Multifunction Inkjet Printer/...

2 Answers

Epson CX 4600

Unplug the printer completely for 5 minutes and try again.

I'l check the error 'code' with Epson. one moment.

May 17, 2008 | Printers & Copiers

1 Answer

How to change ink cartridges on an Epson CX 3800

Be sure you have a new ink cartridge before you begin. Once you start replacing a cartridge you must complete all steps in one session.

1. Make sure the Epson CX printer is on.
2 Make sure the document cover is closed, then open the scanner
Caution: Do Not open the scanner when the document cover cover is open.
3. Press and release the " ink " button. The ink cartridge moves to the check position and the
" On " and " ink " lights flash. If one of the cartridges is low or empty, the printer moves the
cartridge to the _ink out mark.
Note: Don't hold down the " ink " button for 3 or more seconds or the printer starts cleaning the print head.
Caution: Do Not move the print head by hand; this may damage the printer, always press the ink
button to move it.
4. Press the " ink " button again
a. If more than one cartridge is low or empty, the next cartridge moves to the_ink out position.
b. If all of the empty or low cartridges have been identified, the print head moves to the ink
cartridge replacement position.
5. Open the cartridge cover.
6. Squeeze the tab at the back of the empty/low cartridge and lift it straight out.
7. Before you open the new ink cartridge package shake it four or five times, then remove it
from the package.
Caution: Do Not remove or tear the label on the cartridge; otherwise ink will leak.
Do Not touch the green chip on the front of the cartridge, this can damage the
ink cartridge.
8. Place the new ink cartridge into the cartridge holder and push it down until it snaps into
a. Replace any other cartridges that need to be replaced.
9. Close the ink cartridge cover and press it until it clicks into place.
10.Close the scanner.
11. Press the " ink " button The print starts charging ink and the " On " light starts flashing. This
takes about one minute. When it's finished the " On " light stops flashing and remains on.
and the " ink " light goes out.
Caution: Never turn off the printer while the " On " light is flashing or you'll waste ink.
Note: If the " ink " light stays on ( not flashing ), the ink cartridge may not be installed correctly.
Press the " ink " button again and reinstall the ink cartridge until it clicks into place.

Feb 09, 2011 | Epson Printers & Copiers

1 Answer

Cant get it to power up does this printer have a fuse ? its a epson stylus cx 4600

no, it does have a fuse, try to unplug the cable and leave it unplug for a couple of minutes, secure the power cable, if still the same, its a hardware issue.

Feb 12, 2010 | Epson Stylus CX4600 All-In-One InkJet...

1 Answer

My epson cx 4600 dont wat to print

make sure you have the correct driver installed, printers arn't plug n play

Feb 09, 2010 | Epson Stylus CX5400 All-In-One InkJet...

1 Answer

All lights flashing

epson cx 6600 does not tract the paper

Nov 06, 2008 | Epson Stylus CX6600 All-In-One InkJet...

2 Answers

Epson cx6000

Hi slawek, even though your unit is relatively new, it still could need updating the software, I would suggest you update your printer drivers, try this, it should help:

Create a new folder on your desktop and name it newhpdrivers(substitute your manufacturer in new name). Un-intall printer and printer software completely. Go to manufacturers website and navigate to their drivers/downloads or support menu. Select your model, choose the relevant software and download to the new folder you created on your desktop(watch for the light yellow bar at the top of window viewing pane, click on this and choose – download file - . Power down your computer. Reconnect the printer to the computer and turn printer on. Power on pc. Windows will detect new hardware and ask if you have the manufacturers install cd or a location to check for install files. Direct the wizard to your new software, follow the rest of the setup instructions and your done.


Rate Me Please! Hate it? Rate it…Like it, try it!
Thank you for submitting your question to
Would you please take a moment and show your appreciation by rating my performance.
All ratings and comments are welcome. Thank you - anaanymous

Sep 14, 2008 | Epson Stylus CX6000 All-In-One InkJet...

1 Answer


Ive answered your other problem, listed under "epson cx 4600".

Jul 26, 2008 | Epson Stylus CX4600 All-In-One InkJet...

1 Answer

Epson Stylus CX4600

If all of the lights on the control panel are flashing and you see the letter E in the Copy window, the print head may not be able to move back and forth freely. Follow these steps:
  1. Turn off the Stylus CX.

  2. Open the scanner.

  3. Remove any jammed paper or other obstructions from the paper path.

  4. Carefully lower the scanner.

  5. Turn the Stylus CX back on.
alert_note.gif Note: If you can't remove the paper or foreign object yourself, do not use force and do not disassemble the Stylus CX.

And the last thing you could do, is to check if the rod where your carriage slide is dry...if so put a little bit of oil on it

Apr 03, 2008 | Epson Stylus CX4600 All-In-One InkJet...

Not finding what you are looking for?
Epson Stylus CX4600 All-In-One InkJet Printer Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Printers & Copiers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

18258 Answers

Cindy Wells

Level 3 Expert

4719 Answers

Are you an Epson Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides