Question about Candy 24 in. CD622 Free-standing Dishwasher
Hi, The lower door seal is broken on above model causing the dishwasher to leak a small amount during a cycle. However I have searched everywhere for a guide on how to get the old seal off and the new one on but no joy. Any advice appreciated.
not familiar with model. element can be inside cabinet in which case it will be obvious or may be in a cylinder heater mounted in the base. suspect stats as well or possibly the module
Posted on Mar 20, 2007
SOURCE: Candy a8001 dishwasher
It sound that the problem is cause the water level switch. The switch level is usually a diaphragm device with a small clear tube attached between the switch and the bottom of the washer's outer tub. I am not familiar with this specific machine, but if you will open the rear panel you will find it easily. Clear tube first from any obstruction, In case it doesn't help, disconnect the wires from the unit (you should disconnect first machine's power cable !!!!!) and measure with a multi-meter on its tugs for continuity and disconnection while you are inhale and blow to its tube. In case it doesn't react, you should replace it. Good luck !
Posted on Aug 29, 2007
SOURCE: candy cs 455m dishwasher
Welcome to fixya.
I'm Huuum at your service.
You said, Candy keeps blowing the fuse. It is not the main fuse in the house(was checked). I
You think it may be the heating element. You asked any advice?
I feel you have a short somewhere . and who knows where? How old is the appliance and what did it cost?
I've seen 3 or 4 people in the past 24 hours that replaced the heating element in the same candy 455 dishwasher and still had the problem.
They told me they felt they did not want to spend any more money ont his unit cause they said, it was an inexpensive model!
So my clients told me!
Here is an interesting report I just read.
Repair or replace you appliances?
When to pull the plug on your old Appliance
It nearly always makes sense to undertake simple do-it-yourself repairs,
such as replacing a gasket on a refrigerator or a freezer.
Typically, you'll also find a troubleshooting section for more-serious problems
in the owner's manual.
Should you pay for a repair or buy a new model?
The answer depends mostly on the age of your appliance,
how much you bought it for,and the cost of the repair.
Follow these guidelines:
When a repair makes sense.
If your appliance is under warranty or less than four years old
paying for a repair makes sense.
Note that appliances under warranty might require service from a factory-authorized technician;
readers have found them on a par with independent repairers.
When a repair might be a wise choice.
If your appliance is out of warranty and is four to seven years old,
it might make sense to pay for a repair. Customers generally pay $100 to $200 for a repair.
But you might want to buy a new model even at this stage,
given that today's models are quieter and have added features.
Higher energy efficiency is another plus: Energy Star-qualified models made after April 28, 2008,
are 43 percent more efficient than conventional models built before 2001 and 56 percent
more efficient than those built before 1993.
When it pays to replace.
The repair costs more than half the price of a comparable new appliance.
Data also shows that it doesn't pay to fix a less-expensive appliance
six or more years old .
Thanks to better recycling programs, less than 10 percent
of a appliances you replace is likely to end up in a landfill.
Thanks for giving me the opportunity to help!
Please remember to leave a rating before you sign off!
Thank You, HUUUM
Posted on Sep 30, 2008
SOURCE: my dishlex dishwasher overflows
The only part that physically allows water to enter a dishwasher (upon receiving power from the control) is the inlet water-valve. I would test the inlet water-valve located directly where you in-coming water line is connected to.
Shut-off power to the dishwasher and remove the 2 prong connection to the water-valve solenoid (small, black, batter size). Test the solenoid for continuity; if bad, replace the entire inlet water-valve (cost about $20)
Posted on Jan 26, 2009
Tips for a great answer:
Jun 11, 2014 | Asko Dishwashers
Jan 08, 2014 | Candy Dishwashers
Nov 10, 2013 | Candy 24 in. CD622 Free-standing...
May 10, 2011 | Frigidaire 24 in. FDB126RB Built-in...
Dec 23, 2009 | Maytag 24 in. MDB8600AW Jetclean II...
Dec 08, 2009 | Amana 24 in. ADB2200AW Built-In Dishwasher
Aug 27, 2009 | Maytag MDB6000 Dishwasher
Aug 10, 2009 | Dishwashers
Mar 18, 2009 | Frigidaire 24 in. FDBB944C Built-in...
Jan 27, 2007 | Candy 24 in. CD622 Free-standing...
36 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: