Question about Quantum Fireball Lct20 (QML30000LD-A) 30 GB Hard Drive

1 Answer

Hard drive quantum fireball lct 20

Please i nedd to know how do i set up this hard drive as slave, i need to move the jumper to the coreect posicion.

thank you

Posted by on

  • Anonymous Jul 07, 2008

    Quantum Fireball Lct20 30 GB Hard Dr settings


  • fwjs28 Sep 16, 2008

    cept on the webpage thers is no LCT20

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 72 Answers

Go to quantum website, download manual, check for correct jumper settings

Posted on Dec 04, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need jumper setting for quantum hdd 3.5 series fireball lct ,LB10A011 10.1gb to set up as a slave hdd ,thanks


Try this if not then get back to me and i will see if i have another diagram. I had to dig for this info too old haha. i still work with this stuff
ryanfanman.png

Feb 27, 2011 | Quantum (LB10A011) Hard Drive

1 Answer

I want to install quantum 20 GB lct as my second drive and as a slave. I have a six pin connector at the back. How do i set the jumper so as to make it a slave drive thakx jason


Take a VERY close look for some "engraving" near the pins.
Look for 'MA(ster)' and 'SL(ave)' and 'C(able)S(elect)' lettering.

Or, some disk-drives have a diagram on the label on the top of the disk-drive, instead of the engraving. Follow the jumpering-instructions on that label.

Nov 05, 2010 | Quantum Fireball Plus AS (QMP30000AS-A) 30...

1 Answer

Hard disk not recognized


found the solution inside Dell web page - jumper position shown graphically - Thank you, anyway.

Jan 07, 2010 | Quantum Fireball Lct20 (QML20000LD-A) 20...

2 Answers

Different WIndows operating systems on two hard drives


main Dell Optiplex


Slave (cable select)
Quantum Fireball
once you have installed them physically into your comptuer like that, start it up.

Format Quantum Fireball


Now you still have windows xp, and you have a clean 2nd hard drive.

You do not need to install windows xp on the 2nd drive
Quantum Fireball .

Dec 13, 2009 | Quantum Fireball Lct20 (QML20000LD-A) 20...

1 Answer

What are the jumper settings for a quantum Fireball 20 gb HD to set it as slave


looking at the bottom of the drive where the circiut board is ,then turn the connectors towards you, you will see the power connector , then right next to it is the pin setting block with 5 sets of 2 pins second set from the right edge is slave,put your pin tie on that set and your fine

Jul 10, 2009 | Quantum Fireball Lct20 (QML20000LD-A) 20...

3 Answers

Setint the jamper as a 2nd drive and Do i need to farmat it frist


If I recall right this HDD is a PATA (IDE) type. As for the Jumpers please check the following link. The jumper should be as Slave drive.
http://www.helpwithpcs.com/upgrading/install-hard-drive.htm

May 15, 2009 | Quantum Fireball Lct20 (QML20000LD-A) 20...

1 Answer

Problem putting a 30 gig quantum lct 15 3.5"series as a slave


Did you switch the jumper config back to Master or CableSelect before trying to install them as a single drive? Also check the Maxtor website, (they owned Quantum too), for the correct jumper settings. Some of these drives (like the Quantum Fireball lct series) need TWO jumpers not just one.That was the trick that fixed mine from not being recognized by the Bios or the Windows setup disk....I got it used with only a single jumper, but it needed two to put it Cable Select mode.

Apr 07, 2009 | Quantum Fireball Lct20 (QML30000LD-A) 30...

1 Answer

Quantum fireball lct 20


Is it the only drive installed? If so, you may have to reinstall windows from the genuine disk. Check cable to motherboard too and come back to me for more if this fails

Jul 18, 2008 | Quantum Computers & Internet

1 Answer

Quantum fireball 40 not recognised as master


goto the quantum site and verify the jumper setting on the drive first

if correct then.. check your sata cable is good...

check the bios to boot options so the quantum is set to boot...

under boot options .. hard drives.. sort the drive to be the first to boot

Jan 04, 2008 | Quantum Fireball Lct20 (QML20000LD-A) 20...

Not finding what you are looking for?
Quantum Fireball Lct20 (QML30000LD-A) 30 GB Hard Drive Logo

1,029 people viewed this question

Ask a Question

Usually answered in minutes!

Top Quantum Computers & Internet Experts

Jax Planet
Jax Planet

Level 2 Expert

922 Answers

Alun Cox

Level 3 Expert

2678 Answers

Dominion Computer...
Dominion Computer...

Level 2 Expert

312 Answers

Are you a Quantum Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...