Question about Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

1 Answer

Cycle stops, lights blink

This dishwasher will run for a time, and then stop and the display lights will blink.The cycle will not restart.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Cycle stops, lights blink

I have the same problem, same model. Driving me nuts. Help!

Posted on Jun 04, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Dishwasher starts in any type of cycle, runs for a minute, then shuts off as the lights blink out.

in general your wash motor can cause that. It gets old and you can hear the wash motor making a rumbling noise when it turns on. The increased load with cause a thermal coupler to turn the unit off.

Jun 23, 2014 | GE Dishwashers

1 Answer

My Whirlpool GU2400XTP83 stopped during the wash cycle and there is a blinking light above the "light" cycle button. I can not reset the dishwasher, stop or start it.


To reset the dishwasher push in this order the,


the control will be reset...but more importantly how many times ina row does the light will indicate what error code its displaying??

example if it flashes 4 times then a pause then flashes 4 times again its displaying the error code#4
7 flashes then pause then 7 flashes its displaying the error code#7 ect ect


Sep 05, 2011 | Whirlpool 24 in. GU3200XTP Built-in...

1 Answer

Green start button won't stop blinking

START/RESET status indicator light flashing

You have pressed the indicator light flashing START/RESET pad while the START/RESET dishwasher is running. This will cancel the cycle. The light will stop flashing after the dishwasher drains (about 90 seconds).

Press the pad once to start the dishwasher. Press the pad a second time when the dishwasher is running only if you wish to cancel the cycle.

Power to the dishwasher was turned off while a cycle was running and power has just been restored to the dishwasher. The blinking lights indicate that the dishwasher is draining the potential water inside.

The light will stop flashing after the dishwasher drains. A new cycle will start automatically.

Good luck

Nov 29, 2010 | General Electric GLD6966RSS Stainless...

1 Answer

Dishwasher is less than a year old. Once in a while it will stop about 10 minutes into the cycle, then the display lights will blink. Sometimes it will stop and the lights wont blink so we will come back...

I would most likely guess a faulty will cancel the cycle, thinking that the door has opened, and the lights will flash. After a certain amount of time, it might "time out" and reset and the lights would stop flashing. Unfortunately it's a bit of a guess, but the other option would be a bad control board.

Apr 07, 2010 | Frigidaire 24 in. PLD2850 Built-in...

1 Answer

Whirlpool quiet partner III

Hello bckp,
Welcome to Fixya

If your dishwasher does not run or stops during a cycle

Is the Start/Resume indicator flashing? Opening the door or
interrupting the power stopped the cycle. Close the door and
Does the Start/Resume indicator flash 3 times when you
press START/RESUME? The dishwasher is waiting for you to
open the door after the last cycle. Open and close the door,
then press START/RESUME.
Is the door closed tightly and latched?
(NOTE: On models with a dual-digit display, the control
displays “- -” during a cycle if it believes the door is not
Is the right cycle selected? Refer to the “Cycle Selection
Is there power to the dishwasher? Has a household fuse
blown, or has a circuit breaker tripped?
Has the motor stopped due to an overload? The motor
automatically resets itself within a few minutes. If it does not
restart, call for service.
Is the water shutoff valve (if installed) turned on?
It is normal for certain cycles to repeatedly pause for several
seconds during the main wash.

If the dishwasher will not fill

Check the overfill protection float that is able to move up and down
freely? Press down to release.

Let me know if any of these procedures helped you?


Please remember to leave a rating.

Oct 04, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

DU1100 Stops mid cycle.

main control cpu unit failing
needs to be replaced

May 09, 2008 | Whirlpool 24 in. DU1100XTP Built-in...

1 Answer

Problems with Whirlpool dishwasher model GU1500XTKB0

have they checked the thernals on the bottom of the tub

Mar 14, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

2 Answers

Kenmore Ultra Wash Dishwasher LIghts are blinking....

I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Feb 11, 2008 | Kenmore 24 in. 17262 Built-in Dishwasher

Not finding what you are looking for?
Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher Logo

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts


Level 3 Expert

4342 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides