Question about Dishwashers

1 Answer

Zanussi Dishwasher DE6850

Does not seem to be washing properly and will not dry dishes

Posted by on

  • Barbarolly Dec 03, 2007

    I think you may be right. I ran a full cycle again yesterday and the water was cold all the way through. Do you know if it would be worth getting this fixed or purchasing a new one?

  • Barbarolly Dec 03, 2007

    Thank you for your help with this problem.....Barbarolly

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

Sounds like a heater problem to me, does it go through the complete cycle on its own?

Posted on Dec 03, 2007

  • COXY
    COXY Dec 03, 2007

    Zanussi Dishwashers are quite good, it also maybe a thermostat problem, either way it should cost no more than 70 gbp for a local engineer to repair it.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the heating element on a zanussi de6850 dishwasher


remove RHS panel and you will see it bottom right. looks like a round cylinder with wires going into it.

if not heating worth looking at main board as wel for a broken solder joint on heater relay. bit of solder will sort this

Oct 19, 2010 | Zanussi 24 in. DE6850 Free-standing...

1 Answer

I have a Zanussi DE6850 free-standing dishwasher. Have just put on a 65 degree programme. After approximately 1 minute the machine has stopped functioning and the top two lights are flashing and water...


Hello,
You seem to have a blockage,have you checked the filters lately.Also check the drain hose and the pipe that the drain hose goes into,if they are clear then the blockage is down in the bottom of the dishwasher in the pipes or the drain pump.

Hope this helps.

May 21, 2010 | Zanussi 24 in. DE6850 Free-standing...

1 Answer

Electrolux de 6850 dishwasher


Hi,
I followed some of the good instructions already on Fixya. I had checked the heater and it was o.k. I then took the front door of the washer apart to get at the control box. Sure enough, I also had the common design fault. One leg of the rely had scorch marks and was now disconnected from the circuit board. I will solder tonight and test. I include a photo of the burned board. TNoel P8017c86.jpg

May 07, 2009 | Zanussi 24 in. DE6850 Free-standing...

3 Answers

ZANUSSI DE6855 DISHWASHER - NO HEAT FOR WASHING OR DRYING


Make sure you unplug before you start. I had the same problem with a DE6850. The heater was ok. Metered at 25.ohms. Apparently, the relay on the control board mounted in the front door behind the switches is a common fault. Remove the screws around the top part of the door and you will be able to get at the control module. Resolder the connection. Zanussi reliability has been lost. Noel P31bf5e2.jpg

Apr 12, 2009 | Zanussi 24 in. DE6850 Free-standing...

4 Answers

Wont heat or dry


hi have you tried thermostat i repaired on last week same fault

Dec 20, 2007 | Zanussi 24 in. DE6850 Free-standing...

3 Answers

Zanussi dishwasher


hi there sounds like a possible dry joint on the pcb repair and try first

Nov 26, 2007 | Zanussi ZT485 Built-in Dishwasher

1 Answer

Zanussi de6855


most probably the pcb unit...had a few of these changed pcb and cured fault, not a job for a novice to be honest, think the parts is about £70-80 from memory.. ally

Jun 30, 2007 | Zanussi 24 in. DE6850 Free-standing...

1 Answer

Dishwasher was tipped and won't run


I have the same problem if you take off the tray below the front door and set a small blow heater in there it will dry the out the anti flood switch. It usally takes about 25 mins for the machine to start working again.

Feb 21, 2007 | Zanussi 24 in. DE6850 Free-standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

830 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Marvin
Marvin

Level 3 Expert

82313 Answers

Brad Brown

Level 3 Expert

17473 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...