Question about Canon PIXMA iP90 Mobile Printer

1 Answer

Error 300 test print is fine but try to print and get error 300 "printer not responding" powering off/on and rebooting does not fix. Can you help?

Posted by on

  • theheatons Dec 04, 2007

    I can't get the installer to install the drivers. It goes through all the steps of installation, even prompting me to restart my Powerbook. Yet, I still do not get the iP90 as an option when I go to print a doc. And the Printer Utility cannot "find" new printers! Help!

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 77 Answers

OSX support for Powerbooks is VERY sloppy. Try installing the iP90 in "Classic" (OS9.2.2) instead. 922 has built-in drivers for every port on Powerbooks. OSX can't even load a SCSI card on laptops. Or iRda, or any USB above 1.1 etc.... very shabby. Apple was sued for "abandoning" Powerbook support with OSX and LOST a BIG class action. Alternatively, partition your HD with TWO operating systems, and load 9.2.2 as a boot option (with OSX as the other). OSX is "emulating" 922, but this method allows OS922 to "run itself". It is MUCH faster (boots in 10 seconds, compared to MINUTES for OSX) and your iP90 will work on USB or irDa -both! 922 will only need a 700mb partition at least... OSX needs 4gb or more (to accomplish far less, far slower)

Posted on Dec 10, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer not responding


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer (if USB connected)> reboot your pc > unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer (if USB connected). Then try to print again once the computer fully recognizes the USB connection or when the WiFi light on the printer turns solid green (if WiFi connected.).


If that doesn't help, try the steps below:

  1. Disconnect the USB cable connecting the printer from your computer.
  2. On your computer, go to Control Panel > Printers and Faxes.
  3. Delete the Lexmark print object.
  4. Reboot computer.
  5. Re-brick your printer by pulling out the power supply - black box where the power cord is plugged into on the back of the printer, and re-plug after 30 seconds.
  6. When the printer turns on, reconnect it to the computer.
Wait until your computer fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, try to print a document to verify that the problem is fixed.

Mar 27, 2012 | Lexmark X3650 Printer

1 Answer

My Lexmark x4850 has stopped prin?t the computer. What is wrongting . Sometimes it will print when I restar


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.


If that doesn't help, try the steps below:

1. Disconnect the printer from your computer.

2. Re-brick your printer. Pull out the power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds.

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, then try to print a document again to verify that the problem is fixed.


You may also try to update your printer driver by visiting the Lexmark website at http://bit.ly/lY7NTO. Select your operating system, download and execute the file. After the install process, try to print a document again to verify that the problem is fixed.

Oct 23, 2011 | Lexmark Wireless X4850 All-In-One Inkjet...

1 Answer

Printer not responding to print message order


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.


If that doesn't help, try the steps below:

1. Disconnect the printer from your computer.

2. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, then try to print a document again to verify that the problem is fixed.

Sep 12, 2011 | Lexmark X2600 InkJet Printer

1 Answer

I loaded my Lexmark X6180 printer with the software, and the installation went fine to the finish. But I get a communications error message "cannot communicate." What shall I do to fix?


What is the operating system installed on your computer?

A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.





If that doesn't help, try the steps below:



1. Disconnect the printer from your computer.

2. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list again, then try to print again.



You may also try to update your printer driver by visiting the Lexmark website.



If the problem continues, please contact Lexmark Technical Support Center for additional assistance.

Aug 24, 2011 | Lexmark X6180 Printer

1 Answer

Print document system responds document is printing system responds that document is printed but no document is printed. Used troubleshooting for alignment and that works with printer?


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.


If that doesn't help, try the steps below:

1. Disconnect the printer from your computer.

2. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, then try to print/scan again.

Aug 23, 2011 | Lexmark Z816 InkJet Printer

1 Answer

My Printer Lexmark X4580 will not scan. I get the following message-Cannot retrieve Application List. Printing and copying works fine.


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. If your printer is connected via the USB cable, disconnect your printer from your computer. Reboot your computer. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Try to scan again.
If that doesn't help, try to reinstall the printer software on your computer. This will help repair any corrupted files necessary for scanning or printing.

Jun 27, 2011 | Lexmark X4580 InkJet Printer

1 Answer

Printer does not respond to print button for test


REmove and renstall the drivers. Do this through the Printer folder. Delete the printer, unplug it, reboot. If you have the software, use it. If you need the software, get it via download from the manufacturer. Follow the manufacturers instructions as they appear on the screen.

Feb 25, 2010 | Zebra P640i Thermal Printer

1 Answer

Failed response from plugin device


Dirty fix...
When the printer errors out...stop, unplug the power to the printserver. Reset the printer, Clear the print que (delete jobs/restart print spooling service), restart the printserver software and plug the printserver power back in. Wait for the re-detect. Everthing should be good at this point. Unfortunatly the print job will be lost and you need to print again...BUT, NO REBOOT yea!!!
Note... for me, if this sequence is not followed, I will have to reboot. The printserver will be locked for the PC that was trying to print. All other PC's will be fine, and I have no idea why.
Good luck,
Bill

Jun 24, 2009 | Zonet MULTI FUNCTN USB 2.0 PRNT SRVR...

1 Answer

Error code 300. How fix


Do the EEPROM initialize reset;

Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function

0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

May 01, 2009 | Office Equipment & Supplies

Not finding what you are looking for?
Canon PIXMA iP90 Mobile Printer Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2131 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...