Question about Kenwood KDC-516S CD Player

1 Answer

ENTER CODE: BOUGHT FROM EBAY & DON'T HAVE REMOTE TO ENTER KCAR!

I bought this radio from Ebay and it works but it wants the code. I know to enter the KCAR code from the remote but I have an aftermarket remote that does not have the digits on it; just the basic functions and I am not sure how to get this to work from the unit itself as it is set up differently than from the remote. Does anyone have any information on how to get past this to get this radio going? I have my receipt from paypal if necessary! There has been a lot of skepticism but I would just like to once buy something that actually works right! Help?

Posted by on

  • meth1872003 Sep 30, 2008

    i have the same problem but i have the remote kenwood kdc-mp335


×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,512 Answers

KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

Posted on Dec 16, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bought kenwood cd player 7011


Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

Jul 25, 2009 | Kenwood KDC-MP528 CD Player

1 Answer

Kenwood KDC-322


Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press the "Auto" button and "Track up" on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

May 27, 2009 | Kenwood KDC-322 CD Player

1 Answer

Security code for kenwood kdcmp528


for your kdc-mp332 type 2 below will work whith code KCAR entered from the remote

Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Oct 31, 2008 | Kenwood KDC-MP528 CD Player

1 Answer

Kenwood KDCMP528


for your kdc-mp528 type 2 below will work whith code KCAR entered from the remote

Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Oct 29, 2008 | Kenwood KDC-MP528 CD Player

1 Answer

Trying to get the code to a kdc332


for your kdc-mp332 type 2 below will work whith code KCAR entered from the remote

Common Kenwood Security Codes
Many Kenwood radios are configured with the same security codes:

KCAR - This seems to be a "backdoor" to some Kenwood models.
3051 - This is the security code which is printed in the manual of many Kenwood models.
1234 - This is a security code commonly chosen by Kenwood owners.
Entering Your Kenwood Security Code
If the car battery fails or is disconnected, the Kenwood will ask for the security code.

The procedure to enter your security code differs on various models of Kenwood car stereos. Here are three of the more common procedures:

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds until the "..." display disappears.
Enter the security code using your Kenwood remote.
Type 2
Press and hold the "Auto" button and "Track up" (next track button on the right) on the face of radio at the same time until the four dash lines disappear.
Enter the security code using your Kenwood remote.
Type 3: Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset keys until the display shows the letter 'C'.
Enter the security code using your Kenwood remote.
Entering Letters on your Kenwood Remote
To enter a letter using your Kenwood remote, press a button once for the first letter, twice for the second letter, and three times for the third letter -- then press the Track Up or Next Track key to send the letter.

To send the letter 'A', press the 2 key once and then press the Track Up key. To send the letter 'B', press the 2 key twice and then press the Track up key.

Finally, when you are done entering all of the letters, press and hold the Track Up button for 3 seconds.

The key sequence to enter the security code KCAR is:

5
5
Track Up
2
2
2
Track Up
2
Track Up
7
7
Track Up
Your Kenwood should then enter tuner mode.

A Security Code Bug in some Kenwoods
There is a reported bug in the security code handling of some Kenwood stereos. In models with thie bug, the security code is stored incorrectly. The workaround is to enter the wrong security code.

In models with this bug, you have to decrement the third character of the security code by one. If your security code was 1111, you would enter your security code as 1101. If your security code was 9999, you would enter 9989.

i hope this works for you.

Sep 09, 2008 | Kenwood KDC-MP332 CD Player

2 Answers

Security code for a kenwood kdc-319


This is the workshop procedure for resetting the code.

KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!
Please rate me FixYa for this solution. Good Luck :)

Feb 17, 2008 | Audio Players & Recorders

2 Answers

Stereo code


3. Simplified method of clearing the security code
(K Type only)
1. While the code entry is requested, press and hold the
VOL UP key for 3 seconds while holding the DISP key
pressed. (This should turn "----" off.)
2. Enter "KCAR" from the remote. (Same way as the 01
model)
 Press the 5 key on the remote twice, then press the
Track Up key. (This enters "K".)
 Press the 2 key on the remote 3 times, then press
the Track Up key. (This enters "C".)
 Press the 2 key on the remote once, then press the
Track Up key. (This enters "A".)
 Press the 7 key on the remote twice, then press the
Track Up key. (This enters "R".)
3. The security code is cleared and the unit enters the
ALL OFF mode.
4. If you commit a mistake in the code entry, the unit
enters the code request mode again.

Jan 01, 2008 | Kenwood KDC-MPV619 CD Player

1 Answer

Unlock code


KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

Dec 15, 2007 | Car Audio & Video

2 Answers

Need to find out the four digit code



KENWOOD SECURITY CODE CLEAR procedure


Your radio will require one of the following procedures.

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

The security is canceled and the set enters the TUNER mode!

Dec 14, 2007 | Car Audio & Video

2 Answers

SECURITY CODE


Security Code is not accepted.
The code number is incorrect. Please enter code which is printed on your radio passport.
First coding doesn't function.
The code was not entered immediately after first start-up. Put the equipment back into the original operating conditions by pressing RESET key. Then enter the code which is printed on your radio passport.



There are a number of ways to "RESET" (which may or may not solve the problem - proceed at your own risk).
From a G search on the subject...
KENWOOD SECURITY CODE CLEAR procedure
Your radio will require one of the following procedures.
Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.
Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".
Then using your remote enter your code.
Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.
Enter your number from the remote control unit. Your code number is 5227 (KCAR)
* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key
The security is canceled and the set enters the TUNER mode!
when finish all the procedure, is necessary to press "TRACK UP BUTTON" for 3 seconds.. and youre done.

Oct 15, 2007 | Car Audio & Video

Not finding what you are looking for?
Kenwood KDC-516S CD Player Logo

Related Topics:

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4991 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Marvin
Marvin

Level 3 Expert

82322 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...