Question about Procom ML300HGA Heater

1 Answer

Looking for hook up information For Canada

In canada I can not get this unit installed without a ULC number. Is there a way to vent this unit out side Or get a ULC code #

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers
Re: Looking for hook up information For Canada

The Underwriter Laboratories of Canada are an offshoot of the Underwriters Labs of the U.S. They test consumer products for safety. The Procom space heater is advertised as a vent free heater fired with propane. As it is vent free I doubt you can convert it into a vent type appliance. When propane burns, it produces carbon dioxide and water vapor. It must be used with adequate ventilation for combustion. It consumes oxygen to burn. If burning it without ventilation it lowers the amount of oxygen in your room creating a hazard to human life. this is what kills. Perhaps the ULC standards are more stringent then the US but I suppose if the unit has the United States UL emblem, using it in Canada, you may need a direction from your local extension service before you can use it.

Posted on Dec 06, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

We live in Gatineau, Canada, where can we buy the Dimplex switch # DS 3311.

Try contacting Dimplex to obtain the switch you need or possibly information regarding where to obtain it

Jun 27, 2013 | Dimplex Heaters

1 Answer

I live in Calgary alberta Canada. The power cord burnt out, right at the back of the unit. where do I get a new power cord for unit.

Hi, any hardware store will have the cord wire for this unit. They sell it by the foot as needed along with a new plug for it.

Apr 08, 2011 | Presto HeatDish Compact Heater

1 Answer

We are in Canada and it has been extremely cold, however we continually are getting error code 10. Is there something we can do as we do not have hot water at all

10 Air Supply or Exhaust


Ensure Rinnai approved venting materials are being used.

Check that nothing is blocking the flue inlet or exhaust.

Check all vent components for proper connections.

Ensure vent length is within limits.

Ensure condensation collar was installed correctly.

Verify dip switches are set properly.
Check fan for blockage.

Jan 15, 2011 | Rinnai RHFE-1004FA 38,400 BTU Energy Saver...

1 Answer

I have had problems with my Cozy gas wall furnace since it was new (its about 6 yrs old now) I won't stay on. It seems that every year I have to call out service people to get it to work. It always...

if the switch at the top of unit is tripping there is something wrong with the vent , the switch is set at 350 degrees it detects back draft do to a improper vent or blockage of vent, if the installer use the old vent system that is more than likley the problem, have the installer call Cozy tech line at 502-589-5380 so they can go over how the unit is installed.

Dec 07, 2010 | Cozy (W352E) Heater

2 Answers

We installed a Woodchief wc 100c woodstove and i

Hello, I have the same model. The plate on the back say's,install with min installation clearance's side and rear wall 18 inches fire door end 36 inches front 48 inches above 51 inches flue pipe 18 inches install on non combustible and non conducting base of 9/32 inch min thickness that extends 6 inches beyond the sides and 18 inches beyond fire door side. circulating fan type FF-100

Feb 23, 2010 | Heaters

2 Answers

Where is the model # located on my Comfort Glow propane heater?

Just went down in the basement and checked on mine. Looking at it from the front there is a lable on the left side near the bottom. Mine has the model right on the top of the label. CBN18C is my model number, your should be similar to that, only it may have a LP instead of the N mine is natural gas....


Jan 08, 2010 | Desa International CBN30T Central Heating...

1 Answer

No heat after installing honeywell thermostat H8110U

hook up the blue wire in the furnace cabinet where the blower section and the other thermostat wires are connected to the furnace. the thermostat you have uses a common wire from the thermostat to the furnace and this needs to be hooked up in the furnace otherwise you will have the problem you are having.

Dec 07, 2009 | Honeywell Electronic Programmable...

1 Answer

Ceramic Sasco 5123

Sasco Small Appliance Service Company Ltd. 420-28 Street NE CalgaryAlbertaT2A 6T3 Canada 403 235 1020403 273 9714

Sep 17, 2007 | R.A.M. Computers LASCO-5540 Ceramic...

Not finding what you are looking for?
Procom ML300HGA Heater Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Procom Heaters Experts


Level 3 Expert

1751 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

john h

Level 3 Expert

6385 Answers

Are you a Procom Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides