Question about Dishwashers

2 Answers

Kenmore 665 Dishwasher Not Draining

Need Manual. Water is not draining

Posted by on

  • Anonymous Apr 27, 2008

    not draining

  • bobmay50 Jul 17, 2008

    Our dishwasher is not draining. We also found a round plastic piece that has a small whole in the center of it that we couldn't figure out where it came from. The little door that the detergent goes in seems to be making a clicking noise. It is also leaking a small amount of water out of the front of the unit during the cycle. My husband just installed a new sink and disposal. The disposal is on the opposite side this time. We would appreciate any help with this problem.



    Thanks.

    Bob and Mo

×

Ad

2 Answers

After the first try of our dishwasher the water didn't completely drain. Ever since the same level of water hasn't drained from the dishwasher.

Posted on Jun 17, 2008

Ad

Try checking drain lines for the dishwasher for clgs and under the screen in the bottom of the dishwaher

Posted on Jan 12, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

665.13049k110 kenmore dishwasher won't drain.


Check that the drain pipe exit point is higher than the water inlet and drain connection on the machine, thats a comin problem, also check and clean the drain pump situated at the front of the machine at the botom underneath the cover

Oct 03, 2017 | Kenmore Dishwashers

1 Answer

Dishwasher won't run. Worked yesterday, checked curcuit breaker, ok. water is in the bottem of washer but below the float level.


First, check the dishwasher filter and make sure it isn't clogged. Your owner's manual will have simple instructions on how to access and clean your dishwasher's filter.

Next, check the drain hose. Does it look flattened or kinked? Do you see any sharp bends? If so, straighten out the hose with your hands and manipulate it so that it regains its rounded shape.

If your dishwasher drains through the garbage disposal, try running the garbage disposal for a bit to process and clear any food. If that does not get the machine draining, you may have a deeper clog. However, most drain hoses clog either at the main household sink drain line connection or the garbage disposal connection.

Does your dishwasher spray your dishes, but it does not advance to the next stage and drain the dirty water? The timer controls the start of the draining process, so you may need an entirely new timer or a new motor for the timer. Repair service is recommended.

In some dishwashers, standing water is caused by a valve that fails to open and allow the water to drain out. This valve is controlled a solenoid that the timer controls. A malfunctioning solenoid could be the problem.

For more troubleshooting tips and solutions, see Dishwasher not draining. I hope this helps!

Sep 27, 2012 | Kenmore 665

1 Answer

665-110733490 Was working fine ,last night shut it off w/water in the bottom.also pushed cancel/drain did not drain.today I ran A wash cycle but after wash still had same amount water in...


Hello & Welcome to FixYa

Dishwasher not draining completely problem usually occurs due to clogged/blocked drain hose-filter assembly or the drain pump not working. First try to clean the drain hose and drain pump filter located inside the front bottom panel for any clogs, then check drain pump operation. Take off the bottom access panel to clean the drain pump filter and hose. If the problem returns after cleaning then it is the drain pump that needs replacement. Please get back to me if you have any other questions.

Kevin

Jun 09, 2011 | Kenmore Dishwashers

1 Answer

My 665-1312 kenmore dishwasher doesnt drain all the way when finished


Normal 0 MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
Hi,

Here is a tip that I wrote that will help you with your dishwasher not draining problem...

Dishwasher Problems - Water will not drain out

heatman101

Sep 01, 2010 | Kenmore Dishwashers

1 Answer

My Kenmore 665 will not drain!


Hi,
Here is a tip that I wrote that will help you with your problem...

Dishwasher2_bing.gif Problems - Water will not drain out
http://www.fixya.com/support/r4078724-dishwasher_problems_water_will_not_drain

heatman101

May 31, 2010 | Dishwashers

1 Answer

Dishwaser not draining


Hi,
Here is a tip that I wrote that will help you with your problem...

Dishwasher2_bing.gif Problems - Water will not drain out
http://www.fixya.com/support/r4078724-dishwasher_problems_water_will_not_drain

heatman101

May 30, 2010 | Kenmore 15632 Built-in Dishwasher

1 Answer

Kenmore model 665


You need to check the arm's holes for clogs. If the water is filling and draining well, the only water that circulates is being pushed up through the center hole or tower.

The angles of the holes cause them to be little jets when the water rushes out. No water getting through = no jet = no spin.

Jun 30, 2009 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Dish Washer retains the water without draining....


the drain pump is fairly easy to replace. it locks into place beside the sump and motor. push tab in and rotate pump to pull out. you will lose water so have a towel handy. inspect drain hose for restrictions or kinks.

Jun 25, 2009 | Kenmore 24 in. 15079 Built-in Dishwasher

1 Answer

Kenmore 665 dishwasher will not drain


Hi

If the water doesn't drain from your dishwasher, check these:

Drain line/air gap A clog in the drain line or air gap (if there is one) is the usual reason that a dishwasher won't drain. Often the problem is at the point where the drain line attaches to the garbage disposer or household drain line. If you remove this line, you can clear any debris from the hose or hose connection. Be sure to reattach the hose before starting the dishwasher again.

Pump Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pump from inside the dishwasher, but first you need to remove the lower rack, the spray arm, and the spray arm support. 

Look for an impeller--a round plastic fan blade-type of device that spins around. This is the wash impeller, which forces the water through the spray arm. Beneath the wash impeller is the drain impeller, which is similar in size and shape to the wash impeller. The drain impeller pushes the water toward the drain port. These components make up the pump. If any of the pump components are defective, you need to replace them.

Drain valve and/or solenoid Many dishwashers use a drain valve with an electric solenoid. When electricity flows to the solenoid, the valve opens and diverts the water to the drain. Sometimes the solenoid, or the diverting lever, sticks and prevents the dishwasher from draining or filling properly. Try to free up the solenoid to lubricate the lever. Otherwise, you may have to replace the solenoid or pump assembly. With these systems, the motor always rotates in one direction. When it's energized, the drain valve diverts the water. 

Other dishwashers simply reverse the direction of the motor to drain the dishwasher. These units don't have a drain valve. Instead, there's a drain hose connected directly to the pump housing.

Belt One brand of dishwasher uses a belt to drive the pump. If this belt is broken or has fallen off, replace it.

Motor If the motor isn't turning or working, the unit won't drain. First check to be sure you have power to the dishwasher. If not, see the section "It doesn't work at all." If the motor hums but doesn't turn, it may need to be replaced. 

Some dishwashers are susceptible to getting stuck if you don't run them regularly. If you haven't run the dishwasher for more than a week, you may need to manually spin the motor to free it up. If the motor is defective, you need to replace it. Dishwasher motors can't be serviced.

Timer Part of what the timer does is control the motor and drain valve. If the timer doesn't work properly, the water may not drain and you need to replace the timer. This problem is uncommon.


Please do rate the solution as FixYa if found useful and revert for further assistance.


Thanks
Rylee

Apr 08, 2009 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Water fill never stops - never! on Kenmore Model 665-16379301


I had this problem and the drain hose had become disconnected. I had a flooded basement.

Jan 10, 2009 | Kenmore 16919 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

690 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Marvin
Marvin

Level 3 Expert

83081 Answers

Brad Brown

Level 3 Expert

17490 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...