Question about Hoover H130E Front Load Washer

2 Answers

Hoover 1300 washing machine

Hi, my washing machine is stuck at the start of the wsh cycle and will not progress thru the cycle. The start lite is on and will not progrees to show how long to go. 60 minutes.. 30 mintues etc. The machine has taken on water and began to wash but does not progress thru the cycle... have pwr 'd off and on.. held the start switch till all lites flash but no good. Any ideas?

Posted by on

2 Answers

Re: Hoover 1300 washing machine

Any reason why my hoover 1300 washing machine is so noisy when doing the final spin?

Posted on Jan 03, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 75 Answers
Re: Hoover 1300 washing machine

Hi there this is a common fault you will need to replace the control module and selector switch/timer

Posted on Dec 12, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My hoover 800rl top load washing machine does not progress beyond the fill cycle. once the water has reached the set level the start/ pause light goes from solid to flashing and nothing progresses form...

Check owner's manual. The light issue should be covered. Is it possible the tub is over filled? If so the level indicator switch is not working right. I'd unplug for overnight to see if the electronics will reset. Service Technician may be needed.

Feb 13, 2015 | Hoover Washing Machines

1 Answer

Hoover 700LB - fills as per normal and washes but cycle knob does not move, click or progress towards the next cycle therefore washes forever...timer perhaps and if so is it worth fixing?

Hi just read your posting.Does the timer move at all from the original position that you started it from?If it does not move at all then you need a new or reconditioned timer.If it does move but stops at a specific spot,What position does it stop at?Are you in Australia? If so I can give you the contacts on where to purchase a timer.Please reply and I can guide you on how to get the correct timer number for your machine.Looking forward to your reply.

Jul 24, 2010 | Hoover HTC243 Top Load Washer

1 Answer

What Temperature is crease guard. also fast wash on hoover 1300

usually crease guard is a combination of hot and cold (warm depending on water temp and water pressures)

Hoover fast wash is generally a shorted time cycle of the normal washes

Nov 20, 2009 | GE S8000E

1 Answer

I have a Hoover 550 MB Top Loader washing machine . The cycle won't move from wash to spin . it doesn;t progress out of wash cycle , it stays there forever .

Will the unit spin if you manually turn the timer dial to spin? If so, remove power, remove the clock motor from the timer, and inspect the clock and mating timer gearing for debris or damaged gear teeth. At the worst, replace the timer. You may be able to scrape or file the damaged teeth so that the timer will progress.

Oct 19, 2009 | Hoover HTC243 Top Load Washer

1 Answer

Our hoover ultra care 1300 large load washing machine spin fault

The most common cause of machines stopping mid cycle is not draining. Your machine should have a filter behind the kick plate at the bottom.
If this is not the case please post back for further assistance.

Jan 21, 2009 | Hoover UltraCare HC6 130M Front Load...

1 Answer

My 5 year old Hoover 500 mb has started to stop mid cycle or not progress through the cycle !

Mate, I just had the same fault with the same model machine. The local machine repair man called me (i'm a sparky) to double check things for him. The macine stopped at the pre wash rinse part of the cycle every load. He replaced the timer with two NEW ones which both had the same fault as the original. We now suspect an inherrent fault in the timer design but as yet dont have an answer.

Aug 10, 2008 | Hoover Washing Machines

3 Answers

Hoover washer dryer saver 1300

I have inherited a hoover saver 1300 in new flat, the dials have worn away and it goes onto drying mode after wash, how can i have it on wash and spin only - NO DRYING? Thanks

Apr 12, 2008 | Hoover H120M Front Load Washer / Dryer

1 Answer


you need to access your drain pump and check it for an obstruction but when you pull the hose off keep in mind it might have a lot of water in it i usually use a shop vac and pull all the water out through the drain hose before removing the hose or opening the pump sorry i cant be more specific but ive never cleaned the pump on a hoover

Mar 23, 2008 | Hoover AAA140 Front Load Washer

1 Answer

GE Washing Machine

It sounds like the pump may have something stuck in it take the front off and removed the hose's from the pump and check inside the pump for coins etc.. if not you may have to replace the pump I hope this helps.

Dec 21, 2007 | GE WBSR3140DW Top Load Washer

1 Answer

Hoover 1300 spin 5+5 washer dryer

you don't say which cycle it will start on. however, could be cold valve open circuit which also means no rinse or cold inlet hose kinked etc. can you give more info?

Apr 09, 2007 | Hoover H120M Front Load Washer / Dryer

Not finding what you are looking for?
Hoover H130E Front Load Washer Logo

1,272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides