Question about Smeg DWI614 Built-in Dishwasher

Open Question

SMEG SA627X Dishwasher goes Pop!!

My SMEG SA627X dishwasher has started to go pop towards the end of the wash cycle. It seem to function correctly but the popping is so loud that you would feel that something is going to catch fire.

Anyone have any ideas?

Posted by on

6 Suggested Answers

  • 1 Answer

SOURCE: Smeg dishwasher

Hi, You can download SMEG dishwasher manuals from here: Al.

Posted on Feb 10, 2007

  • 944 Answers

SOURCE: Error message on Smeg dishwasher

Sorry couldn't find the info online - try these guys, they are the official smeg service agentsm and they have a live chat feature too -perhaps you get lucky and they will tell you the problem; Hope this helps - if you get no luck from them then please post again :)

Posted on Apr 23, 2007

  • 641 Answers

SOURCE: smeg dishwasher wash cycle freezes ,

Thanks for the information.

Posted on Jul 24, 2007

  • 1462 Answers

SOURCE: E2 error in smeg dishwasher

e2 is overfill or flooded base.
take the bottom front panel off and see if there is water in it and if so, mop it out. if it reoccurs, then you have a leak.
you will see a float device in the front approx middle and this is what actuates e2. if fault is intermittant, try putting a small weight on this - a washer for example.
if e2 is being caused by overfill and not a flooded base, then the water intake moulding needs replacing

Posted on Nov 20, 2008

  • 1 Answer

SOURCE: smeg dishwasher dwf 44 ss 1

Posted on Feb 15, 2009

  • 8197 Answers

SOURCE: DWF614SS smeg dishwasher E8 error code

The E8 fault is generated when the internal switch on the alternating valve fails to register that the diverter valve has switched over. It may be that the disc inside your valve isn't moving completetly over or the switch isn't working. The feedback from this device is to the main pcb, therefore there are only three parts involved, the pcb, the diverter valve and the wiring. It is possible to test the valve using a multimeter to confirm it is indeed switching properly.
I don't have a part number unfortunately but if you go to you'll be able to get the part number and price of the part.

Good luck with your repair.

Posted on Apr 13, 2010

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


1 Points

Related Questions:

2 Answers

Why does the door pops open when starting

I would check how level the dishwasher is. Might need to adjust the feet.

Aug 14, 2014 | Meiko FV 40.2 Dishwasher

1 Answer

Dishwasher cavitates. I have a Smeg DI612CA9

Does the drain hose loop up to the top of the unit before going to the sink drain? If it goes down first it may be siphoning or draining by gravity.

Aug 08, 2013 | Smeg Dishwashers

1 Answer

My smeg dishwasher seems to be permanently in wash mode. The light on the menu of settings no longer flashes, but permanently is on, and when I run a load it never stops. I hear the two beeps as if the...

You have a timer relay issue ,probable need a new board for it ,a cheap fix would be to time it and see how long it take to run full cycle and put a regulaer outlet timer on it or a alarm off your stove or what ever,save a couple of bucks

Feb 16, 2011 | Smeg STX2 Dishwashers

1 Answer

Detergent dispenser on SMEG DWF 44SS1 doesn't open during cycle - any ideas?

this is Usually caused by a tablet sticking in the Detergent Dispenser. This will stop the Detergent Dispenser from opening at the correct time on the wash cycle.

Oct 18, 2009 | Smeg 24 in. DWI612 Built-in Dishwasher

1 Answer

SMEG dishwasher - cycle buttons

What is the model of the dishwasher? Open the door and look down the right hand side for a sticker and repost please. As a rule number 3 is a normal wash :D

Mar 23, 2009 | Smeg 18 in. DWI410 Built-in Dishwasher

1 Answer

Dishwasher Whirpool not finishing a cycle.

control board issue needs to be looked at by whirlpool tech in your area, still under warranty

Apr 10, 2008 | Smeg PLA8743XU Full Console Dishwasher...

1 Answer

SMEG DI 612CA. Dishwasher

Pisss!!! Comin from my asss!!

Mar 04, 2008 | Smeg Dishwashers

1 Answer

My Smeg dishwasher DWF 64 SSE won't go onto rinse or dry

Easy one first try this to see if it helps

Water pre-heating
Your dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is cool, the heater may take up to half an hour to heat the water.

To avoid the wait, increase the incoming water temperature before turning on the dishwasher. Do that by running the kitchen sink faucet until the water runs hot. Or increase the temperature of the hot water to the entire house at the hot water heater.

Warning! To lessen the risk of scalding, don't set the hot water heater temperature higher than 120 degrees Fahrenheit.

Jan 29, 2008 | Smeg 24 in. DWF612WH Free-standing...

2 Answers

Smeg dishwasher

Hi, You can download SMEG dishwasher manuals from here: Al.

Feb 02, 2007 | Smeg CSU2001 Built-in Dishwasher

Not finding what you are looking for?
Smeg DWI614 Built-in Dishwasher Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smeg Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Starnley Johnwells
Starnley Johnwells

Level 3 Expert

1029 Answers


Level 1 Expert

25 Answers

Are you a Smeg Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides