- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
First make sure the "Eject" button has not stuck while pushed-in. Clean the Tray window/opening and the inside of the front part of the tray. Then try to push the tray in a little bit when closed and drag it out while open! By the time dust gathers on the greasy tray rails resulting it not to open and close to the full extent. If it helps but the problem comes back, then you should open the box and clean the rails more thoroughly. Have a look at the switch that senses the tray state (open/closed) too. OBS! That is not the same as the "Eject" button! Switch placement is device model deppendant but it is usually placed on the stationary part of the disc-player unit under the front end of the tray in the middle!
Some units do eject a disk they don't recognize. That a player can't read a disk could be a result of incompatibility, dusty optical lens or faulty/old laser. You may clean the lens by using a "Cleaning disk" or blowing with an air spray(or a straw with your mouth) through the opening of the tray.
Good luck Please rate positively if helpful, thanks!
Either the sensor and/or the laser lens inside the tray are dirty, a common fault printers)or you are not aligning the disk properly when placing in the tray. You can try using a CD\DVD cleaning disk and a can of compressed air to blow out dust. If this fails uninstall the printer's drivers and software and reinstall everything from the beginning. If that fails return for repairs. NEVER use stick on disc labels, only use write on discs
My husband adjusted the CD/DVD tray, then we selected the icon that looks like a wrench on the printer's message window, then "restore default settings" on it. Turned computer off then on again, and it FINALLY started working again :)
Please follow these steps: 1. Turn your printer on. Most power buttons are located on the top of the printer. Press and hold down the button until its LED light turns green.
2. Choose the image or text you desire to print onto the CD. On your computer, open the image or text you desire to print. images should be opened by clicking on your computer's "Start" icon and selecting the "Pictures" tab folder within the Start menu. When the Pictures folder opens, click on the image you desire to print onto the CD to enlarge it. If you are planning to print text onto the CD, open the text in Microsoft Word or any other desktop publishing program you may have on your computer.
3. Insert the CD into the printer. Press the "Eject" button that can be found on your CD printing enabled printer. A CD tray will open automatically. Place the CD into the tray print side up. Close the CD tray. The printer will begin working to detect the CD. Once the CD is detected, your printer's LED light will either flash green or another indication color.
4. Print the image or text onto the CD. For image printing, click on the enlarged image's tab that will be on your computer's taskbar. You will see a horizontal row of action icons below the image. Click on the thumbnail image of a printer to print the image onto the disc. For text printing, simply click on the "File" action on the navigation menu in your desktop publishing document. Click "Print" within the "File" drop down menu. The image or text will be sent to the printer once you choose the "Print" action.
5 . Remove the CD from the printing tray. The CD will be fed through the printer during the printing process. Once the process is complete, the CD will come through the bottom of the printing tray. Take the CD from the tray when it reaches the bottom.
The above mentioned steps must help you. In case of any difficulty please revert back.
Disconnect the printer from the computer. Turn it off & make sure the CD/DVD tray is closed then turn it back on.
Here's generic instruction for you:
If you are receiving an error pertaining to the CD TRAY NOT BEING INSERTED CORRECTLY, please do the following:
Recommendations: -Don't force the CD/DVD tray into the printer. -Make sure your printer is powered on, and the output tray is in the upper position. -Please ensure there is at least 3 inches of space behind the printer, or the CD tray may eject.
Included, are the correct CD/DVD loading instructions. Please follow the instructions below:
CD/DVD LOADING: 1. Ensure the printer is powered on. Remove any paper from the sheet feeder. 2. Push in the paper support extension on the printer, and close the paper support. 3. Push in the output tray extensions, but leave the tray open. 4. Lift the output tray. Place one hand on the top of the printer, and pull up on the output tray until it stops. Lay the tray down in the upper position. 5. Place the CD or DVD into the CD TRAY with the white (or printable) side facing up. Note: To print on small 8cm CDs, please place the small CD ring on the tray first, then place the CD inside the ring. 6. Slide the tray into the tray guides located in the output tray. Push in the guide until the arrow on the tray matches up to the arrow on the tray guide. 7. Press the PAPER button to load the CD/DVD into the printing position. The CD is correctly loaded when the printer's POWER button stops flashing.
General tips for CD and DVD printing: -Burn data/video/images onto CDs or DVDs before attempting to print on them. -Do not use thermal-printable or regular CDs or DVDs in the printer. -Moisture or fingerprints on the printable surface of the CD may cause marks or smearing to appear after printing. -All printable inkjet media is different. Some surfaces will absorb ink better than others. If output appears banded, faded, or streaky, print a Nozzle Check pattern to confirm that all colors of ink are printing completely. If the ink does not completely dry or smears after 24 hours curing time, you may need to use the Epson Print CD tools to adjust (lower) the print density. -The only supported resolution for CD/DVD printing is 1440 dpi (aka "Photo") -Borderless printing and printing on the "inner circle" (plastic around central hole) of CDs is not supported. -Do not use the "print preview" feature provided by the Epson printer driver as it will only show the image on a blank field and does not offer a clear indicator of where the image will print. -The Epson Print CD software works best with JPG images and may not import some TIFF images.
Sorry a little late only just read your problem. The location is not the bottom tray feeder but the disk tray. In settings change your media type to "Printable Disk" the paper scource should automatically change to "Disk Tray" and hopefully every thing will work OK.
1. make sure there is enough room to the rear of the printer to allow clearance for the try to pass out the back and back in. 2. when initiating the processes and thing start to happen gentle pressure on the back of the try to help the start the ball rolling helps 3. Do examine the lead in strips at the front of the try to ensure they are no distorted.
And 4 a search og Google and EBay can reveal a revised design tray for a modest sum. Finally take a look at www.fixyourprinter.com.
Clean the white parts on the caddy and also clean the entry/exit rollers (use windowlene and a sponge). If you still have problems see my previous posts about under head cleaning and just complete a quick clean.