Question about Philips VRX342AT S-VHS VCR

1 Answer

Philips model no. vrz242at22

I dont't have instruction and would like to know how to use with dish tv

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 476 Answers
Re: philips model no. vrz242at22

Follow this link to download your manual:

Posted on Feb 25, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My universal Philips remote dont have a "code search"button' or a "set-up button,what can I do

The subject header says it does and all the Philips remotes I am familiar with have it.

Jun 07, 2014 | Philips PM-4S Maganvox 4 Device Universal...

1 Answer

I can't get my phillips vr 260 to operate at all,I dont have an instruction manual

check above link and download for free

Thanks for using FixYa - a 4 THUMBS UP rating is appreciated for answering your FREE question.

Feb 20, 2011 | Philips VCRs

1 Answer

Would you happen to know the 3 digit manufacture code for a Sharp VC-H992U Video Cassette Recorder? I need this info to input it into my TV so that the VCR will work with the TV. The TV provider is Dish...

Hello! Here is the link to our remote codes, if that fails follow these additional steps for the Power Scan this should resolve it as well.

  1. With the desired equipment on, press and hold the correct Mode button until all mode button backlights illuminate (about 3 seconds), then release.
  2. For AUX mode Power Scan ONLY: press 0 for a TV, press 1 for a VCR/DVD, press 2 for any other device, then press *.
  3. Press and release the Power button.
  4. Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off.
  5. Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.
  6. To verify the code works try several different functions for that equipment.

Daniel Busa
DISH Network Customer Service

Dec 23, 2010 | Sharp VC-H992U VCR

1 Answer

Ineed to know how to interconnect our tv, vcr, dvd and top set box, Can you help? Philips DVP3120/05, Philips VR720 Philips 282 tv with built in dvd and Bush free view top box.

Problem solved : incorrect connection of scat leads Solved by roof top digal aerial Digi top box and on to VCR. and then on to TV.
Scart from VCR to TV
Scart from VCR to DVD
Scart from Digi Top Box to TV.
Everything now functions correctly
Equipment connected:
Philips VCR: 720/07
Philips TV : 28PW6515/05
Philips DVD: DVP3120
Bush top box

Nov 20, 2009 | Philips VCRs

1 Answer


Easiest way to connect is with a scart connector from VCR to TV, then just select AV1 from TV (this will depend on what type if TV you have). If you dont have scart, put your aerial into the rear input of VCR, take supplied flylead & connect that from rear output of VCR & connect other end into TVs aerial socket. Insert a pre-recorded tape, press play on VCR & then on TV select channel 0 & tune your TV until the play back picture appears, then store this on TV tuning settings.

Jun 19, 2009 | Philips VCRs

2 Answers

I cant record tv through my vcr.

set the vcr up so that you change the chanels through the vcr,,,check the vcr setup menu

May 16, 2009 | Philips VCRs

1 Answer

Sylvania vcr/dvd installation

!st) The antenna INPUT::RF (black wire usually from "cable TV", "Dish TV", even ANTENNA air wave reception,etc.) into INPUT of VCR\DVD, OUTPUT of VCR\DVD to TV RF input.
2nd) If you have INPUT\OUTPUT to what are called " RCA " jacks on your TV, on the front or on the back, then any & all output jacks from VCR\DVD goes to INPUT\OUTPUT of the TV.
In other words:: output of audio on VHS\DVD to input of audio on TV( RCA jacks). Output of video on VHS\DVD to input of video (RCA jacks)
Hope this helps

Aug 14, 2008 | VCRs

1 Answer

Remote control code for Philips VCR & DVD player DVP3340V/17

If you have Dish Network and I suspect if you have Direct TV or a cable providers, you can use your remote for that service provider to find your VCR code. For the Dish you can look in the user's guide on pages 9 and 19 to see how to do a "Device Code Scan" and "Check Device Code".
To Scan: #1: Turn on the device you wish to scan for a code, #2 Press and hold down the button on your Dish remote for that device until all the buttons light up and the specific device button is flashing, #3 Press the blank power button, #4 press the up or down button until until your VCR tuns off, #5 Press the POUND ( # ) key to store the code number and #6 Press the blank power key to turn the device back on.
To Check the Device Code: #1 Press and hold down the device key until all buttons light up and the device button is flashing, next press the POUND ( # ) key TWICE ! The Mode button will flash to code number with a pause between each number, i.e. 5 flashes, pause 3 flaskes, pause one quick flash is 530. Write down this number and you are rady to go !

Nov 16, 2007 | VCRs

Not finding what you are looking for?
VCRs Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips VCRs Experts

Robert McClure

Level 2 Expert

160 Answers


Level 3 Expert

4502 Answers


Level 3 Expert

93738 Answers

Are you a Philips VCR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides