Question about Black & Decker 9072CTN Cordless Screwdriver

1 Answer

I have a old cordess screwdriver that i love and have replaced the battery pack years ago .IT'S time again.

The model is a 9019 , type 1, 3.8v. cordless screwdriver the battery pack has a number on it . 9647mx ..... 3 batteries in series aprox 1 1/4" high and 7/8" in diameter all soldered with push on connectors
Is this available ? where , how much , how fast?


Harvey Presement

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 313 Answers
Re: i have a old cordess screwdriver that i love and have...

I say no. battery is more expensive that the drill.better buy new same type of drill

Posted on May 29, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I need an 18 volt battery (part number 982038-001) for a craftsman drill

Interstate All Battery Center replaced my two batteries for $45.00 each. They replace the defective batteries and place 'date stickers' on the battery packs (982038-001).

Sep 16, 2012 | Craftsman Drills & Drill/Drivers

1 Answer

Milwaukee tool 18 volt nimh battery won!t charge

If the battery pack is more than 2 years old its time for a replacement. The typical charge/discharge life cycle of a rechargeable cell is 500 - 700 times and the shelf life is about 3-4 years from the date of manufacture. If the charging indicator lights up when you dock the battery on to the base and still does not work after 5 hours - its due for a replacement.

Apr 08, 2011 | Dewalt Accessories Batteries 18 Volt

1 Answer

Purchased the two lithium and charger combo about two years ago. I use my Ryobi drill and flashlight in the garage and around the house no where near commercial/professional levels. About three (3)...

How long have these 2 batteries been standing idle without being charged? Lithium ion batteries can still discharge if left for too long. There is a voltage detector which detects whether the cells are too far discharged to be safely charged again and if that occurs the circuit is broken and the batteries will be deffective in the charger.
I have had the same problem with these and other LI batteries. Answer is replace the batteries and then make sure they are given a quick charge on a regular basis. However common advice seems to be that LI's should not be kept fully charged, but just partially charged until needed, then charge them for use, especially if usage is sporadic

Nov 14, 2010 | Ryobi Two 18V Lithium-Ion Batteries +...

1 Answer

I need to replace the batteries but I can't get the old batteries out of the screwdriver. I've pried and pried and the pack is part way out.

buy some Johnson&Evenrude lubricant (marine) .Spray up into the cylinder. then use vice grips to pull the battery out. Maybe wedge a nail into the push prongs to hold them in.

Oct 21, 2010 | Black & Decker Pivot Plus Cordless...

2 Answers

My old black & decker power screw driver will not accept a charge. I cannot get it charged up.

Black & Decker stopped doing battery packs for the older screwdrivers, like the 9018, some time ago so you cannot get them.

However you can still buy replacement NiCad, Sub C, 1.2v, tagged batteries that will do the job on the older 2.4v models as NiCad batteries for use in power tools are exempt under the European ban on importing NiCad batteries where used in power tools (Specific Exemption).

When you open up the screwdriver look at the positioning of the batteries and the tags/connectors and solder them together the same way.

So all you need is a soldering iron to join the centre tags together and then trim the end tags, top and bottom, to the width of the live/negative connectors and you have got a new battery pack.

It doesn't have to be pretty but after a small investment and a little effort it sure beats paying out £30 to £50 for a new screwdriver. I have done this for my older Black & Decker and Bosch screwdrivers which all work like new again.

Apr 08, 2010 | Black & Decker Pivot Plus Cordless...

2 Answers


These generally have a 2 year warranty and I'm sure these are well out of warranty. Afraid that they really aren't a repairable item as you'll probably find it will be cheaper to replace them. But call the Customer Service line all the same and they can put you in contact with the Service Centre in your area - 1800 444 224

Nov 10, 2009 | Drills & Drill/Drivers

2 Answers

Tired old Dewalt dw056 impact driver

It needs a new battery pack. Rechargeable batteries eventually wear out and no longer hold a charge. The tool runs only briefly and the battery is exhausted again. The big home centers and online sources sell replacements. There are also companies that say they can rebuild your battery pack at much lower cost than replacement. I have no experience with them.

Apr 23, 2009 | Dewalt DW056 18 Volt Cordless Impact...

1 Answer

Remove the pins on a B&D electric screwdriver 9019, to remove the cover and to change batteries

use a end of a small nail to tap it on thru'. replacement is just the reverse [don't need new pins if you are careful!]

Jun 21, 2008 | Black & Decker 9072CTN Cordless...

Not finding what you are looking for?
Black & Decker 9072CTN Cordless Screwdriver Logo

Related Topics:

460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Drills & Drill/Drivers Experts


Level 3 Expert

2363 Answers


Level 3 Expert

56925 Answers

Jim Thurston

Level 3 Expert

669 Answers

Are you a Black & Decker Drill and Drill/Driver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides