Question about Philips TV Tuner Video Capture PCI Card - Phillips Digital (652101138177)

1 Answer

Tv switches itself off to standby

My tv always switches itself off to standby so we will have to switch it off fully with the power button and then on again. this has been goin on for about 16 months now since we were given the telly. however the problem is getting worse and now we constantly have to keep switching the telly back on. please help !!!!! our tv is a 32in toshiba not sure of the model number... thankyou

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 57 Answers
Re: tv switches itself off to standby

Sounds like a fault in the remote receive circuit or power supply. ambient electrical noise is getting into the circuit somehere. As it is not a new TV, I would suspect power supply capacitors, as they dry out with heat and age. Probably best to take it to a repair shop that gives free estimates/quotes, as there may be more on its way out and this is the first symptom.

Posted on Dec 18, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

I have connected my jvc combi player to my tv via a scart cable. I then select the source button on my tv remote control and select scart. I can do and auto scan and it says completed, but no signal.

When using a scart cable, the TV should switch over to the Scart port that as last came active. Even when you switch on and choose the menu on the device, the TV should notice and switch over.
Just check if you are using a normal scary cable. Sometimes not really compatible cables with in / out switches, can spoil the fun, because not all wires are connected correct.

Jul 21, 2014 | Audio Technica TV Accessories

1 Answer

Telefunken TLED-26FHDPA has a blinking red light and cannot switch on using remote or switch on tv

The subject is TV accessories but you are describing a TV fault which likely is power supply failure

Jul 13, 2013 | TV Accessories

1 Answer

Radio locked,entrred code wrong 4 times

Leave it SWITCHED ON...UNDISTURBED for as long as it takes to automatically reset itself

This could take several hours

Mar 26, 2011 | Philips SAA7130 TV Tuner/FM Radio/Video...

1 Answer

Television inputs keep telling me that i have no signal or no input when i try to switch over and use my ps3. this is weird because i was using it when this problem occurred, so everything should be...

Try resetting the signal from the PS3.
Press the power button and hold it until you hear a few beeps in a row.
Power it off again, then back on.
Make sure to have the TV set to the input the PS3 is connected to & turned on before starting the PS3.


Mar 26, 2010 | Samsung (TN-RBNG10) TV Input

2 Answers

My plasma tv want turn on

there could be the following reasons. If there is the red light on indicating the power reaching the TV then your power supply unit may be faulty. Open the back cover and look where the power cord goes and meet the components inside and it would also have a transformer like thing on it. This is the PSU module. If any of the capacitors is bulged or burst then that needs replacing with one of exactly the same specifications. Do that. Second is that there is no indication of the power reaching the TV. In that case check the plug and the wall socket and also the power on switch on the TV. Whatever is faulty should be replaced.

Nov 20, 2009 | Philips TV Tuner Video Capture PCI Card -...

1 Answer

My windows xp wont detect my trying to connect my mobilepre usb can someone please help me solve this?

First ensure you have any software installed the the M-Audio needs My Oxygen keyboard needed the software to work properly.

Also do not extend the USB cable and make sure you use the proper power supply my Oxygen would not work 100% until I got a power supply for it

I devised these simple steps that tend to remedy quite a few issues with most USB portable / external hard drives and OTHER devices (though not always)

A few things to check but assumes USB and Windows for other interfaces / operating systems (mac/ Linux) similar steps may be adapted to suit.

1. Ensure it is connected directly to the computer to a USB 2.0 port not a USB 1.0 port as this can have effects on performance and reliability

2. Use only the cables that came with it NOT one that fits that may have been lying around or is longer. Not all USB cables are equal even though they should be)

3. Do not connect through an external USB HUB unless that hub is USB 2.0 AND has its own power supply.

4. Use ONLY the power supply that came with it if it has an external power supply Don’t use any other unless you know it has both the same voltage and current rating e.g. 12V 500mA anything rated below that would not work properly.

5. Always use the same port for connecting your devices. Some devices do not like being switched about. If switched they may want to install software / drivers again. This can be especially true if you move a HUB to another port

If you checked and fixed anything there and still have issues then check your hardware from CONTROL PANEL / SYSTEM / HARDWARE.

Any exclamation marks by hardware need fixing before you investigate any further

USB flash drives can fail for no apparent reason.
Sandisk Cruzers are especially bad for this.

USB hard drives should be treated with extreme care.
This is a real hard drive ! and knocks and bumps can quite literally kill them.

It is possible to remove drives from the enclosures in most cases and connect directly inside a PC to fully check it.

Note that if you hear a drive clicking or pinging this could be the worst thing you would hear.
Known as "The Click Of Death"

If none of the above steps help look at updating the drivers from the manufacturers web site in the support section.

Sep 15, 2009 | M-Audio MobilePre (US41401) Audio Input

2 Answers

Phillips 32" tv stuck in standby mode

thesupply is not responding
take your tv for repair
let them check power supply
semi conductors, transistors, zener diodes, an dfuse resistors, also check the switch contact,
and fuse,

Dec 24, 2008 | Philips TV Tuner Video Capture PCI Card -...

2 Answers

Hdmi switcher

you need use the remote learning method to correct this, for some reason it seems that if you just push the buttons on the hdmi switch box ie, inp2 to switch to a second hdmi output, after about 5-10 min it will revert back, but if you use a infared remote set to switch it, it stays.

Jan 03, 2008 | Matrix Video Storm CRM84D HDMI,...

1 Answer

TV keeps turning itself on and off, onto standby

Right i had this same problem for ages! i cannot explain why but when i uplugged my DVD player (which was flashing its light at the same time as the tv for some reason) the TV has worked fine.

Aug 24, 2006 | Philips TV Tuner Video Capture PCI Card -...

Not finding what you are looking for?
TV Accessories Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips TV Accessories Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Gareth Cockram
Gareth Cockram

Level 3 Expert

657 Answers


Level 3 Expert

2598 Answers

Are you a Philips TV Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides