Kadak Easy Share 5300 printer. Screen reads "Paper Jam Clear Jam

You can try clearing this error by resetting your printer. Follow these steps, Its worth a try.

1. Press and hold the “*” key.
2. Press the “#” key and release both keys.
3. Display should say “Enter Special Key Combo”
4. Press and release in sequence the “1”, “2” and “3” buttons.
5. Screen should say “support” R0631M”
6. Press and release the right arrow button until the display says “System Configuration Menu”.
7. Press and release the “OK” button.
8. Display should say “Hardware failure status”. If not there already, Arrow Key over to “Hardware failure status”,
9. Press and release the “OK” button.
10. Display should say “Hardware failure status: Clear. Press OK to clear”.
11. Press and release the “OK” Button. Message changes to “Hardware failure status Cleared. Press Cancel to continue”.
12. Press and release the “CANCEL” button as many times as necessary, so that, either the “Welcome to Photosmart Express” screen appears, or, the “Ink System Failure” screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.
13. Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.
14. Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer
15. Turn the unit on. The printer may display message “USE POWER BUTTON TO SHUTDOWN THE PRINTER” followed by “PRESS OK TO CONTINUE”. Press OK. The Printer
will start the “ONE TIME INK INITIALIZATION PROCESS”. Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.
16. Press Setup menu on the All-in-One then scroll using the arrow key and select Print Report then select Self Test Report.

Let me know if this help you.
Thank you for using Fixya.

If paper is jammed, a Paper jam message will appear on the control panel display.

Follow these steps to clear the jam:

1. Gently pull any jammed paper out of the output tray or sheet feeder.
   
   
2. If the paper is stuck inside, turn off the Epson Stylus CX.
   
   
3. Open the scanner, remove the jammed paper and torn pieces, close the scanner, and turn the Epson Stylus CX back on.
   
   Note: Be sure to check the far left of the carriage area when checking for jammed paper. Paper that is jammed there may be hidden from view.

If paper jams inside the Automatic Document Feeder, clear the jam as follows:

1. Open the Automatic Document Feeder cover and remove any jammed paper.
   
   
   
   
2. If necessary, lift the document cover and remove any paper that has jammed inside.
   
   
   
   
3. Press OK to clear any messages on the display screen.

Go to kodak.com/go/itg and follow the step by step troubleshooting. If you still get the same error,Time to contact Kodak at 1800 421 6699 and Your printer will be replaced free of cost.

print cartrige cradle is stuck clear jam then press ok in hpphotosmart 7550

Try this one
Take out the inks and printhead
Leave the cartridge door open, then unplug the power cord from the back of the printer while the access door is open
Close the cartridge door once the cord is unplugged
Reconnect the powercord, turn on the printer, then your printer will look for your printhead "Printhead missing or not installed correctly..."
Then put everything back. make sure it will snap in to place. Then print a calibration page, then scan it. This is just over writing the error message.
Thanks Josh - Kodak Tech Support

well! the machine says that there is some paper in the machine, start by taking different itrems out such as the paper tray, look in the doc feeder and so on, good kuck

Paper jam means that the rotation of the roller is not smooth, either because you are not inserting the paper correctly or there is something stuck in the printer. What you have to do is open the back cover of the printer and check the roller and clean it. Then if still paper jam is there, then it's manufacturing problem. Contact manufacturers.

hi,
CANON PIXMA MP160 All-In-One InkJet Printer has few common problems. Such as Driver CD lost, Scanner does not work, Connection problem etc. For find all these software solution just click here....


http://www.canon.com/printer/prob676ijt65/solution

prirweto-i-23

A paper jam error message will appear if the printhead is not correctly installed. Try removing and reinstalling the printhead again, but make sure it snaps into place. Try loading a sheet of plain paper and press at the same time copy+cancel; hold them down until the printer feeds the paper. The paper will go through the rollers and come out blank.

unplug it..both cables..wait around 1 min..try it again. got backup?