Question about Kenwood KDC-MP528 CD Player

1 Answer

KENWOOD KDC-MP728 MY MOTOR FOR THE CD PLAYER STOP WORKING, WHAT COULD CAUSE THAT? I CANT PUT IN A CD WITHOUT FORCING IT.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do you hook up the mp3 player to it?????

Posted on Dec 27, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Recently the CD player stopped working with a cd inside it says error 1/error 2 after it trys to load it also won't eject the cd at the same time this started the usb also stopped charging my devices


Try to put another cd in on top of the stuck one . don't force it , just push in a little ways then pull it out . Sometimes that will make player eject the stuck one. I would take it back to whoever installed the radio.

Dec 05, 2015 | Cars & Trucks

1 Answer

A friend forced a cd into the player on my 2003 Silverado. It will not eject or let me put another one in.


negative you will have to remove the radio and reset by unpluging and pluging back the power plug

Jul 13, 2012 | 2004 Chevrolet Silverado 2500HD

1 Answer

I put a cd in the player and its stuck inside. how do i get it out without smashing the player?


Possible that there was a fault in the CD , maybe warped that has caused the CD to get struck inside. It can also be due to the failure off the loading mechanism of the player.
Hence you will require the hexahead tools to remove the mechanism so as to retieve the cd from the struck up mechanism.Remove the lid , then observe the mechanism , remove the mounts and release, thereafter check if the motor works , if not the loading motor drive IC , motor or the processor can be defective. ,

Oct 30, 2010 | Philips HTS-6500/37 System

2 Answers

Player will not read cd . Cd will not spin


Without me seeing it, it usually cannot read the disc and is caused by a defective, or needs to be adjusted or cleaned, laser assembly as long as it is every cd put in it. It can also be the disc spinner motor. Either one of those is the most likely cause. :)

May 19, 2010 | Yamaha CDC-845 5-Disc CD Changer

1 Answer

Denon CD player DCD 920. When using the open/close button once, the CD-door opens but when it is open, without any waiting time, it immediately closes again. If i operate manually the open/close switch on...


Off the power, and plug off the switch, and try opening it manually. DO NOT force open it. I don't think it would close back since it has no electricity already.

Oct 14, 2009 | Denon Audio Players & Recorders

1 Answer

CD PLAYER JUST SUDDENLY STOPPED WORKING, CAN'T GET CD'S OUT


Sounds like the motor inside player is shot. You will have to pull out player, remove top cover, remove 2 screws holding cradele and remove your cd. Than either install new player or have a new motor put in yours.

Jun 22, 2009 | 2001 Chevrolet Suburban

1 Answer

Car stereo wont accept disk (motor doesnt pull it in)


you are correct it is not "seeing" the disk with it's infared sensor to repair this sensor you must disassemble the radio

Apr 30, 2009 | 2007 Ford Focus (3 Door) Hatchback

3 Answers

Sony CDX-L480X


I had the same problem, CD not accepted by unit and pressing source button to select CD player causes unit to display reset.
Using reset button just causes unit to 'whir' for a while, problem is not solved. Firstly with unit switched off, and the ignition off I inserted a CD using some gentle force, I then inserted a second CD, forcing it in over the top of the first. Next I pressed and held the reset button for a short time before releasing it. Both CDs were ejected, when the unit had stopped I took the CDs out, replaced the front panel and turned on the ignition, The unit will now accept CDs and eject them O.K.

(This did take two attempts to get right). Seems to reset the eject status of the CD player.

Avulon

Feb 17, 2008 | Sony CDX-L480X CD Player

1 Answer

Emerson PD6810 CD Boombox Error


My older model PD6810 had the spindle that holds the CD on the player missing causing the ER message to show and the player to stop working.

Aug 21, 2007 | Emerson PD6810 CD Boombox

2 Answers

CD Player Issue


the system has problems reading burned CD's u cant fix it or anything windman

Jan 30, 2006 | RCA RP-9316 Boombox

Not finding what you are looking for?
Kenwood KDC-MP528 CD Player Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4930 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

79024 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...