Question about Peavey TLS115X Speaker

1 Answer

Just stopped working!

1 of my subs didn't work last night. been using a bridged 1200 wtt pwr amp to run 2 subs. is there a fuse inside that I could replace?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Does it powered on? any bass at all?

Posted on Nov 30, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hifonics colossus-ltd dual monoblock amp does not have much output, running a cerwin vega stroker dual 2 ohm sub wired 4 ohm load bridged


Bridge at 4ohms your only getting 600watts rms. You will need to bridge at 1ohm (parallel) and adjust the gain accordingly. This will give it 1600 watts rms. If you would of had a dual 4ohm sub, then you could of bridged it at 2ohms mono, but you can't you have to go either 1 ohm or 4ohm. I believe it's not getting enough power.

I’m happy to help further over the phone at https://www.6ya.com/expert/chris_7f7f91eb941fb23f

May 20, 2012 | Hifonics Colossus-ltd Dual Monoblock 3200w...

1 Answer

I Have a Sony Xplod 800 watt amp and 2 12 inch Sony Xplod subs


You should definately bridge them. Firstly, lay the 2 speakers face down next to each other. Note the connections +- +-. The first + will go to the amplifier. The next terminal(-) will be connected to the next speaker(+). Take the last(-) and connect to amplifier. Please note that your amplifier has a bridge section which is normally the first + and the last- on the two channels. Connect your woofers on the bridge.

May 28, 2010 | Sony XM-ZR1252 Car Audio Amplifier

1 Answer

Car audio amplifer blowing fuses


why are you in stereo for subs? mono all the way.

Feb 21, 2010 | Kenwood KAC-7252 Car Audio Amplifier

1 Answer

Can i run just 2 subs on this 1200 watt kenwood 5-4-3 and if so what way will i get the most power, i mean do i bridge it or pute the speaker wires in other ports


you can run 2 subs given that you dont go over 2 ohms of resistance and that the subs are rated at 1000 watt max each around 4 or 500 watt rms. if your not sure about ohms dont bridge it and get single voice coil subs. this amp is capable of about 700watts constant power 1200 max spike if the voltage stays at 12 or higher.

Feb 05, 2010 | Kenwood KAC-X650D Car Audio Amplifier

1 Answer

1000 watt amp problem. Speaker + Wire


hey wats up, let me see if i cud help u out here...i will give it a try and use bigger wire, the prob. cud b the wires cnt take pwr thts running through them, but tht cud only b the reason if ur wires are small...other thn tht u cud check 2 see if all ur fuses are correct & thy aint letting 2 much pwr through tht cud the prob as well...let me kno how tht gose & if those dnt wrk there might b sum thing else we cud *** up wit.

Jan 28, 2010 | Car Audio & Video

2 Answers

Two terminals? bridging theory?


Hello again jm129852,

Having two power and ground terminals allows you to run two smaller wires instead of one big one. It's a convenience. No, you do not have to use them both. They are connected together inside. Yes, you should still use a single fused battery lead. Connect the big wire and fuse holder to the battery and to a distribution block and run the smaller wires from the output side of the distribution block.

When you connect the outputs of a two channel amp to two separate speakers, each speaker gets the power produced by it's channel only. If you are using only one speaker, and the amp is rated to operate bridged, then the speaker will receive the power from both channels, typically twice as much. You do need to be careful when using bridged mode because many amps will only operate safely at a higher impedance when bridged. For example, when operated with both channels connected to separate speakers (not bridged), it may be stable to 2 ohms. But when you connect both channels together (bridged), it is only stable to 4 ohms. Usually, the specifications will tell you the lowest impedance at which the amp should be operated. The specifications for the current RF Punch 500.2 are like this: 125 watts X 2 at 4 ohms; 250 watts X 2 at 2 ohms; 500 watts X 1 bridged at 4 ohms (4 ohm stable in bridged mode). You would NOT want to connect two 4 ohm subs in parallel to this amp in bridged mode. It would result in a final 2 ohm load and the amp would overheat and fail. One 4 ohm sub would be OK, and it would receive the full 500 watts as stated in the specifications. You could connect four 4 ohm subs, two each in parallel to each channel, and the 2 ohm loads on each channel would be OK. Or you could series two of them together for an 8 ohm load, do the same with the other two, and then parallel the two 8 ohm loads for a final impedance of 4 ohms and connect them into the bridged terminals. With DVC subs the connection possibilities get more complex. There are many good impedance calculators online that can help you determine the best wiring solution for various amp/sub combinations. I like the one above at the12v.com web site. Rockford-Fosgate also has one which allow you to select the a number of subs (up to 4), their voice coil configuration (single or dual), and the voice coil impedance. The RF calculator then shows you what configurations are available and what your final load impedance will be.

Hope this helps.

Apr 28, 2009 | Rockford Fosgate Punch 800a2 Car Audio...

2 Answers

Amp or something cutting out.


Power caps store power from the battery and they feed constant power to the amp so you dont get no drainage! this could be one reason..

have you bridged both subs and wat gauge wire are you using.

these amps can only handle one bridged sub at 4ohms and this amp is recommended that u use 8gauge or higher. if your running to subs i normally reccomend using 4 gauge power wire as you get more rms power feed to the amp

you can get a power cap or anyother accersory cheap online at my suppliers.. caraudiosecurity << click to enter >> hope this helps and please rate me :)

Apr 22, 2009 | Rockford Fosgate Punch 401S Car Audio...

2 Answers

SUBS


Hi , you need to replace with thick wire , if possible attache fuse or circuit trip overload protection you may ask to thew radio store .

May 07, 2008 | Polk Audio EX12 Car Speaker

3 Answers

Hifonics bxi 1206d


make sure you have a 40 amp fuse in it
im going to try to describe this to you
to bridge a amp this is for 2 ch AMP

+ - + -
I 2 2 I
I 2 2 I
I I 22
I I 22
I I 22
I I 22
#1 SPEAKER #2 SPEAKER
WIRE WIRE
ONE GOES ON THE POSIVE OF ONE SIDE AND THEN THE NEGATIVE OF THE OTHER
HOPE THIS MAKES SINCE
PLEASE LEAVE MY RATING

Feb 11, 2008 | Hifonics Brutus BXi 1206D Car Audio...

Not finding what you are looking for?
Peavey TLS115X Speaker Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peavey Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5575 Answers

Michial Gueffroy

Level 3 Expert

1138 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Peavey Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...