Question about Maytag Neptune MAH5500B Front Load Washer

3 Answers

Error code Washer stops mid cycle.  nF is the code on the machine.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Error code

My problem was simply that the screens where the hoses connect to the washer were clogged with rust from my well water. I cleaned them and we're back in business.

Posted on Sep 12, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers
Re: Error code

I kept getting the same NF code! I pulled out the washer turned off the water to the machine. You willl need a pipe wrench or tool to unscrew nozel. I unplugged the machine. Unscrewed the nozels put a towel down so water dont run on your floor that was left inthe line. You will see a yellow tab where the hot water hose was attached and a blue tab where the cold water was attached it has a screen on it pull the tabs with your finger or with pliers rinse well and it will remove any sediment dirt that came through the line. I rinsed mine put them in the way u took them out connect your hoses snuggly turn on the water before pushing the machine back in place to make sure it is not leaking. plug in the machine. I started my machine and it worked perfectly and the water pressure was excellent. no more code.

Posted on Mar 20, 2012

Re: Error code

NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water. This also can occur if there is a whole-house water softner, well-water, or very low water pressure.

Posted on Dec 04, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Nf code and donnot continue to next cycle

Samsung Washer Error Code NF (Fixed ...
Jan 11, 2014 - What does the error code NF mean on a Samsung washer? ... You can set the washer to any cycle and test each solenoid for proper voltage. ... Next would be to check the screens on the back where the water hoses connect. ..... Hi, you don'thave any power to the water valve wires when it should be filling?

Dec 15, 2015 | Frigidaire Affinity ATF7000E Front Load...

3 Answers

I have an error code that says nf

Hello & Welcome to FixYa

NF error in your washer is displayed due to no fill condition, when the washer tries to fill but is unable to nf is displayed. Please check the water inlet valve for any clogs and obstructions, you can also clean the inlet to solve the issue. Please get back to me if you have any other questions.


Mar 06, 2011 | Samsung WF337AA Front Load Washer

1 Answer

It stops about 13 minutes from the end of the cycle, right before it spins. It displays NF.

""It stops about 13 minutes from the end of the cycle, right before it spins. ""

NF is no fill for the FAV6800A and FAV9800A are you still having the issue.

To me it sounds like you have two issues
""It stops about 13 minutes from the end of the cycle, right before it spins. "" with no additional info this could be a issue with the Clutch Pulley. Did you take any error codes like DC or UC?

Are you going to DIY the fix or call in a repair service?

Jan 26, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

My washer stops mid-cycle and the screen reads "nf" what does this mean?

nf= no fill
either your water valve is not working your water is not on
or the sceens are clogged where the hoses connect to the back of the washer
the first thing
i would check is the scrrens
if those are clean ensure the water is on...
turn the unit on as normal, you should hear a buzz or hum from the water valve try to open
no hum its probably bad
a very easy repair that can be done by you very simply

the part can be found at appliance parts pros
one word

Nov 02, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Washer stops with "nf" displayed on screen

nf is no fill
with samsungs most of the time its a bad resistopr on the cold water vale itself,
check your screens though

Oct 03, 2009 | Samsung WF337AA Front Load Washer

1 Answer

When i am on spin cycle it stops and has a nf error code! what can i do?

This error code, pops up usually when in the spin cycle, your clothes are out of balance, too heavy of a load, or even at times it can happen with a too light of a load. Just stop or pause your washer and re arranged the items inside,

Jul 08, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag neptune TL

The machine needs to cut you a break;

“”i have a maytag neptune TL and there are several things wrong with it...1. I can't wash small loads it will stop at the spin cycle and flash dc””

This issue is a clutch issue see this post to DIY the repair.

“”it will wash fine on regular loads until it comes to spin cycle again and it will stop and flash nf””

This one is a little confusing the “nf” error is a No water fill error code. Check these two post for support regarding water inlet restriction or valve not opening properly.

nf post nf post 2

“”my fabric softener dispenser will not let the softener out neither will the bleach dispenser””

See this fabric softer post for support. The fabric softener dispenser may be clogged or the water dispenser valves feeding both dispensers may not be operating properly. The Service Manual on page 16 “Board Output Test” will give you support to turn on the Fabric Softener Valve and Bleach valve. See if you hear the valves operate in Service Mode”

My method may seem a little confusion for viewing water flow to the dispensers. This issue could be associated to the nf error you are receiving, restricted water flow (inlet screen clog) or cold water valve not working properly.

Post back for any questions or possible support I can offer. I’m an owner like you not a repair person but I’m very comfortable working on this machine. Rich

Jun 17, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Hi... My washing machine... samsung front load. will stop in the middle of the wash and beep and flashes nF. We had bought the floor model and when we got it home realized we didnt have a manual... I can...

nf is the failure code for [no fill].check your water valve screens for a mineral buildup/blockage.they are where the fill hoses attach to your washer.make sure water is present at washer[run the water from each hose into a bucket].i live in ohio its 0 degrees out side now.i did't know it but there was an air leak near my dishwasher drain hose in the house and water froze in it blocking the drain.i hope this info helps you fix this washer, God bless ,tom

Jan 16, 2009 | Samsung WF337AA Front Load Washer

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

719 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides