Question about Philips 32PT5441/37 32" TV

1 Answer

Phillips my tv just stopped working turns on and off on its own now flashes the lite on the on and off button 3 times then 2 then 1 over and over

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers
Re: phillips

See Duplicate post............................T.

Posted on Nov 28, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have a Sylvania TV with dvd/vhs attached and do not have the remote. I can't get the tv on channel 3 to watch cable. I have tried numerous universal remotes but none of them have worked. Please tell me...

Here is a process to program a Vizio Universal remote. I saved this info to my computer as a text file some time ago. Can't remember where from, so if it works, no credit to me. :-)

Sylvania:10054, 10030, 10171, 11944, 11931

1. Manually turn on the TV.

2. Press and release the TV button.

3. Press and hold the SET button until the LED blinks 2X.

4. Enter your Codes

If the code is accepted, the LED flashes twice after the last digit is entered.

If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed.

5. Point the remote control at the TV and press the POWER button. The TV will turn off.

Vizio Remote Reset

(Use this step if the LED doesn't blink twice after entering the above codes)

1. Press and release the TV button.

2. Press and hold the SET button until the LED blinks 2X.

3. Type 9-8-2, the LED should blink 4X.

4. Now follow the steps above for Programming the TV again.

Jul 07, 2014 | Standard (CRT) Televisions

2 Answers

Hello i need codes for asda's universal remote model URC20-D1F so i can sync it with my BEKO tv please can you help?


Set up by Automatic Search

1. Turn TV on
2. Point the remote at tv and Hold SET and TV buttons at the same time and keep pressed for 3 seconds.
3. The LED flashes and the remote control starts the automatic search.
4.The OFF signal is automatically sent to the tv from the remote control.
5. Once the TV switches off press any button except SET to stop auto search.
6. Switch your tv on using the POWER button.

Dec 27, 2010 | Beko 142746 TV

2 Answers

Need remote control code for dish network along with how to instructions. I can't locate my manual for my Zenith

Try this...1) turn on your tv set manually.2) on you dish and hold the "TV" mode button next to the "SAT" button.when all of the other mode buttons light up, let the "TV" button should be flashing.3) Press the blank power button(The top red button in the top center of the remote).4) press the UP or DOWN button at the rate of about 1 per second until the tv turns off.4) When the tv turns the # key on the bottom right of the remote...this stores the code and you should be ready to go...please try this first..It should work.If the scan doesn't work...The only code for Orion is "694".I hope this was helpful....

Jun 15, 2010 | Zenith C32V37 32" TV

1 Answer

Red standby light flashing wont do anything

turned on and off at mains switch 2 or 3 times light stopped flashing and tv now working alright

Jan 27, 2010 | Philips 32PW6506 32" TV

1 Answer

Flashing green light

Did you try this yet

If the TV will not respond to either the remote control
or the front panel controls and/or will not power Off,
press the SYSTEM RESET button with a pointed item
like the end point of a paperclip. The TV will turn Off
and the TIMER light will flash quickly for about one
minute. When the TIMER light stops flashing, you may
turn on the TV again. Changes you made the last time
the TV was On before you used the SYSTEM RESET
button may be lost, however, the changes you made
previously are not lost.
The green light is a multi-function indicator. This light
will flash rapidly for about one minute each time the TV
is plugged into the wall electrical outlet, when power
is restored after a power failure, or using the SYSTEM
RESET button. Do not attempt to turn on the TV again
during this period. Wait for the flashing to stop and
the light to turn off, before attempting to turn the TV
on. While the TV is powered on, the light illuminates
steadily. If the TV has been programmed to turn on
automatically using the Timer feature,

Sep 21, 2009 | Mitsubishi WS-65515 65" TV

1 Answer

Watching tv when the picture went black and now the green on light flashes for 30 times and turns off

A green flashing light for this model of TV indicates that the lamp cover is open on the TV.
  1. Unplug the power cable to the TV.
  2. Remove the 2 retaining screws on the lamp cover with a Phillips type screwdriver.
  3. Remove the lamp door completely from the TV.
  4. Remove the two retaining screws on the lamp case.
  5. Lift up the fixed wire handle of the lamp.
  6. Pull out the handle slowly and remove the lamp case.
  7. Insert the new lamp gently into the correct position. Make sure it is inserted correctly.
  8. Using a manual Phillips screwdriver (Do Not use an electric screwdiver), tighten the screws you removed in
    step 3.
  9. Replace the lamp cover and tighten the cover screws.
  10. Plug in the power cord and turn on the TV. After the initial warmup period (which may take up to several
    seconds for full picture brightness), the TV should operate normally.
If any of the following conditions exist, turn off the TV, unplug the power cord, and repeat steps 1–9 to ensure that the lamp unit and lamp unit
door are installed correctly:
  • The lamp indicator flashes green.
  • No picture
  • Dark picture
  • TV will not turn on
If, after repeating steps 1–10, the problem still exists, call Customer Service at 1-800-631-3811.

Aug 31, 2009 | Toshiba 44NHM84 44" TV

2 Answers

Code for p1300ntv to work with directv remote

You can "manually" find your code by  1. pressing tv button on the remote 2. press and hold setup until TV button blinks twice 3. press 991, the tv button should blink once 4. slowly press and alternate the power and tv buttons until tv turns off.   5. press setup to lock in the code when tv turns off.
hope this helps,  j 

Jan 14, 2009 | Disney 13" TV

1 Answer


Install horiz driver kit # 483513057673...applies to all L04.01U
chassis.......+ replace 47mf/25v cap in driver circuit.........T.

Nov 27, 2007 | Philips 32PT5441/37 32" TV

5 Answers

Remote codes

You can find the remote control codes for different brands of devices from

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or your brand is not listed, and you are still not able to get the unit to respond, try the following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when you reach the end of all the codes for this device type.
  1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing the following steps.
  1. PRESS and HOLD the SETUP button until the red LED flashes twice.
  2. PRESS 9 - 7 - 5, the red LED will flash twice.
  3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
  4. PRESS the button that will receive the learned function, the LED will flash rapidly.
  5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keys or press and hold SETUP until the Cinema's red light flashes twice to lock in your new feature. (If the red light does not blink twice, stop and repeat steps through 6).
To test the new feature, press and release the device key in which the new feature was learned followed by the key on which the feature was learned

More help for programming your remote can be found here:

Hope that helps! Should you have any further questions, please feel free to post them here.

P.S. - If you find that the solution/answer I provided led you to, or resulted in a fix, please close the ticket with a FixYa! rating. I would be very grateful for your show of appreciation.
If it hasn’t, please do not assign a rating just yet. Please post back as to what steps you took, results, etc, and I will try to assist you further as best I can. I am here at your service.

Thank you for using FIXYA!


Sep 09, 2007 | Haier HTF20R21 20" TV

Not finding what you are looking for?
Philips 32PT5441/37 32" TV Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Standard (CRT) Televisions Experts

Sp Gupta

Level 3 Expert

655 Answers

Jim Evans

Level 2 Expert

186 Answers


Level 3 Expert

485 Answers

Are you a Philips Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides