Question about Linksys PrintServer for USB with 4 port Switch: PSUS4 (NTSVLS0PSUS4) Print Server

1 Answer

PSUS4 problem "talking" to Canon S330

My PSUS4 worked flawlessly with my Canon S330 up until recently. Now my print jobs never make it to the printer. If I connect my printer directly to any computer, it responds. When connected to my PSUS4 I am unable to print.

I've gone through the mandatory 30-60 second reset test with no luck.

I've tried running a "test" print from the admin interface with no luck either.

I do not get any error messages or any indication of failure.

Posted by on

  • dreaddymck Nov 27, 2007

    RoadHawk
    Thank you for your response. The PrintServer 'PSUS4" is connected to the router. Think I am able to reach the print server because I have access to the "admin" interface for the printserver.
    I have tried printing a "test" page from within the admin interface with no luck. Again, no error message or any other indication of failure. My print request doesn't appear to get sent to the printer...or at least not completely. Occasionally i've seen printer respond as if beginning a print, but then nothing happens.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Hi dreaddymck
I need a little more information on the setup. Is there a router in your network? If there is, is your PrintServer connected to the router and your computer is attempting to connect to the printserver through the router? If there is no router and your PrintServer is connected to your printer via the USB port and your computer is connected to one of the ports on the PrintServer via a cat5 cable, I would check to see whether you are actually communicating with the PrinterServer by pinging its IP address from the computer. If the ping is successful, then I would look at the printer properties in your computer's printer control panel and check the port configuration. Usually it is shows the IP address, port 9100 and port protocol is usually set to RAW. Otherwise I would attempt to reinstall the PrintServer using the CD originally provided. It appears to me that the server may not be publishing its IP address on your network.
--RoadHawk

Posted on Nov 27, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Schematics for seting up a printer


Configure and wire your systems as shown in the attached power point presentation.moz-screenshot.png 5f10200.tif

Jun 02, 2010 | Linksys (PSUS4) Print Server

1 Answer

The ink absorber on my Canon S330 photo is full, so cannot print. I cannot get my printer to the two repair centres suggested by Canon as I live in Wales. Is it possible to obtain the replacement part and...


the ink absorber on my Canon S330 photo is full, so cannot print. I cannot get my printer to the two repair centres suggested by Canon as I live in Wales. Is it possible to obtain the replacement part and fit it myself, please?

Mar 08, 2010 | Canon PIXMA iP1800 InkJet Photo Printer

1 Answer

I have had this printer for over a year and it has worked flawlessly until about 3 weeks ago and now it takes about 2 minutes after I click on print for the printer to activate. Any suggestions?


If your X3550 prints OK when it does start, perhaps the selection for printing immediately when receiving a print job has been changed to printing after entire print job has spooled.

This selection can usually be toggled between these two choices.

Jan 14, 2010 | Lexmark X3550 All-In-One Printer

1 Answer

Linksys not printing


as it is very old print server
u need to update its firmware ( software )
contact 1800-546-7114 for same ( linksys tech. support )

Apr 01, 2008 | Linksys PrintServer for USB with 4 port...

2 Answers

Can't print to mac wirelessly (could do it a few days ago)


I had the same problem until recently. You have to install the drivers FROM THE CD that came with the printer, instead of selecting the drivers from the default list. Then, when selecting which printer driver to use (you'll have two options) choose Canon IJ and NOT Canon MX310 series. This is a problem with their MX310 driver, which is solved using a default/generic Canon InkJet (hence, the IJ) driver. Hope this helps!
P.S. This only works on Mac OS X. I have yet to figure out how to print wirelessly through Vista. Will keep you posted.

Mar 28, 2008 | Canon PIXMA MX310 All-In-One Printer

1 Answer

Network printing


I am afraid, PSUS4 is an older model of print server , which supports only ordinary printers. All in ones are not supported by PSUS4. Linksys have other print server which works with all in one printers. The model number is WPSM54G. Probably you can try that. Also, if the PSUS4 is less than one month old, you can get it replaced with the WPSM54G from the stores itself . The WPSM54G can be used as wired as well as wireless to the router. If you want to use the PSUS4, you may need an ordinary printer like Office jet or laser jet with USB 1.1 version.- Thank you

Oct 26, 2007 | Linksys (PSUS4) Print Server

1 Answer

JOB STOPPED WHEN I TRY TO PRINT PDFS


Sounds like a software issue not the prnter. Try uninstalling adobe if this is wat the program is and reinstalling.

Aug 22, 2007 | Canon PIXMA MP810 All-In-One InkJet...

2 Answers

Canon Pixma 1500


Plug the cable for the printer into a different USB port and download the newest drivers from the Canon website.

Jun 28, 2007 | Canon PIXMA iP1600 Printer

Not finding what you are looking for?
Computers & Internet Logo

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2268 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...