Question about Hotpoint Washing Machines

1 Answer

I've got hotpoint toploader secondhand no instruction how do you connect to water supply Wmtl79?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hotpoint Master
  • 63,596 Answers

With 2 hoses usually 1 hot 1 cold

Posted on Jun 01, 2019

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jumptrout51
  • 3361 Answers

SOURCE: connecting washing machine to water

One for hot water one for cold.
They both must be hooked up or water will run on the floor.

Posted on Apr 24, 2009

beltronic205
  • 1481 Answers

SOURCE: hotpoint washers says check water supply but water

could be solonoid valve faulty

Posted on Apr 07, 2010

oldTech2332
  • 2341 Answers

SOURCE: Can u run hotpoint wmtl79-d/dg washing machine

yes it can be used only on cold water
if what your asking is that if you only have one hose to connect to it that cant be done the water valve where the hoses attach to must be capped off on the hot side or water will leak out of it
so yes only cold be used but must cap off hot side inlet at machine

Posted on Jul 21, 2011

  • 6277 Answers

SOURCE: Hotpoint WMD960 on start says ' no water supply '.

Hi from retired Englishman in SW France,

If you have checked that the hot and cold water taps are turned on fully and the hoses are not kinked or squashed at the back, it is worth while checking both the hot and cold water inlet filters. Turn the taps off and remove both hoses at the washer end. Inside each inlet port there is normally a little filter which should just slide out. Clean if necessary and replace each one and the hoses.
If after turning the taps back on there is no improvement, the problem is symptomatic of a malfunctioning hot or cold water control valve. Sorry but it needs a service call and a check that it isn't the control PCB ;-0(

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck,
John C

Posted on Aug 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My machine won't empty


blow through your outlet pipe and see if its blocked. and clear your water trap if it has 1

Apr 26, 2015 | Hotpoint WMTL79 Top Load Washer

1 Answer

Wmtl79


is it spinning at all? if so then check ur pump for obstruction or bad propeller, if not check door switch, clutch, motor coupler, belt etc

Jul 09, 2014 | Hotpoint WMTL79 Top Load Washer

1 Answer

No cold water coming out


Check where the hose connects to the washer sometimes their is a screen filter in their. If not the valve that controls the water input could be bad. Most of those valves are where the hoses hook to the washer.

Aug 22, 2012 | Hotpoint WMTL79 Top Load Washer

1 Answer

My hot point will not fill with water the supply is ok


The screens where the hoses connect to the washer are clogged with mineral deposits, which is not allowing the water to flow into the washer. I've had the same problem.

Sep 03, 2011 | Hotpoint Ultima WDM73 Front Load Washer /...

1 Answer

Can u run hotpoint wmtl79-d/dg washing machine just on cold water


yes it can be used only on cold water
if what your asking is that if you only have one hose to connect to it that cant be done the water valve where the hoses attach to must be capped off on the hot side or water will leak out of it
so yes only cold be used but must cap off hot side inlet at machine

Jul 21, 2011 | Hotpoint Washing Machines

1 Answer

My WMTL79 machine has a burned melted lid


Probably caused by a bad connection, or loose wire, nothing more serious than that .

Jan 25, 2010 | Hotpoint WMTL79 Top Load Washer

1 Answer

Connecting washing machine to water


One for hot water one for cold.
They both must be hooked up or water will run on the floor.

Apr 24, 2009 | Washing Machines

1 Answer

Hotpoint WMTL79 Top Load Washer. no water entering the drum.


Remove the front panel and open the control panel.
Remove the platic hose from the water level switch and the air dome on the side of the tub.
Clean the soap out of the air dome hole witha toothpick Blow through the plastic hose. Re-connect everything. Set the washer to spin and turn it on for 1 minute.
Then run a regualar wash cycle.

Mar 19, 2009 | Hotpoint WMTL79 Top Load Washer

1 Answer

CLOTHES NOT SPINNING DRY


you have something stuck in the pump..a sock maybe or some other small article of clothing

Jan 11, 2009 | Hotpoint -Ariston VVSR1030HWO Top Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1234 Answers

gbob59

Level 3 Expert

3042 Answers

James Hehling
James Hehling

Level 1 Expert

11 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...