Question about Canon NP 7130 Black and White Copier

1 Answer

Ploblem It shows the sign of 03 and inverted 83 in the conrol panel and then the copier stop the copying process.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers
Re: ploblem

The error code you are refering to is not an inverted 83 is in actuality an E803 flashed by an E8 followed by an 03.Basically your 24V dc is either being shorted somwhere internally or the DC controller or composite PCB needs to be replaced in either case the cost associated with replacing either curcuit board would far exceed the value of the copier.

Posted on Jun 07, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Why my canon ir1133 printer is showing e733/0000 error message?

ERROR E733-0000 Stops printing and shows sign "Turn ...
Nov 20, 2013 - ERROR E733-0000 Stops printing and shows sign "Turn main power ON". Error ... error message when printing d1350 imageclass. Jan 03 ...

Oct 29, 2015 | Canon imageRUNNER 1133 Laser Multifunction...

1 Answer


Clean the 2 registration sensors and the registration clutch. Mostly this is caused by paper dust to the 2 registration sensors. This sensors is easily removed by opening the side cover , you'll see the registration sensors at the lower part of the drum unit. There is only 1 screw holding this. Remove that screw and slide it to remove.

Oct 27, 2014 | Toshiba OEM ESTUDIO455SE 45 PPM...

1 Answer

F-28-1 curently appears on my screen

F 28-01 High voltage power supply abnormality.
Ihe charging ON/OFF operation has been performed five consecutive times since the charging trouble detection signal was detected at start of charging.If there is a paper in copying process when this jam occurs,the machine stops after completion of copied paper ejection.Verify the charge wire,change and the holders.Check the high voltage unit.
F - 28 -02 Toner transfer wire malfunction
F - 28 -03 Toner separation wire.malfunction

Feb 11, 2013 | Konica Minolta Konica 7020 7022 7025 7030...

1 Answer

Canon ir2420 restart the machine if ploblem persists,call service representative E000003 0000

On the operator control panel, next to the nine key pad,is a button that says "additional functions" locate it and we will perform a 3 step function that will allow you to enter "service mode" which will let you clear the code. Press "additional function", release it and then immediately press the 2 and 8 buttons simultaneously, release them and then press additional functions again. As I said this is a 3 step process that should be done in a smooth but timely fashion. If done properly this will summon a new screen that will show you a few "blocks" and the top block will say COPIER. Press it and a new screen will appear which will have several blocks across the top of the screen. One will say FUNCTION and you need to press it. Again a new screen. Look at the menu in the body of the screen and you will see CLEAR. Press clear. New screen again and look for ERR. Press ERR. After you have touched ERR notice the "OK" button in the lower right corner of the screen. Touch "ok". Now unplug the copier and power off. wait a few seconds.Now plug that cable back in and power on. The copier will attempt to return to a ready condition by "warming up". This is where the copier may notice a problem with the temp. Then make a copy. This will force the copier to run a brief diagnostic(which you wont see). If the copy successfully exits the copier then you should be ok. But the fact that the code occurred at all Means that at a minimum the copier had previously seen a problem and so the code may return. Good luck and take care

Feb 06, 2013 | Printers & Copiers

1 Answer

When i take a copy it shows three wide black lines

check ur drum for these lines while stopping the copying in between the process.if u can remove the lines with cloth then u have to change the drum blade. this is related to drum section

Aug 04, 2011 | Canon iR 2016i Black and White Copier

1 Answer

Printer stops printing after first page and show the following on the second page: INTERNAL ERROR - Including Corrupted Data POSITION : ox23759 (145241) SYSTEM : h6fw/x1_image VERSION : SPL 5024...

Try disconnecting your printer from your pc and then uninstalling the drivers for it in your control panel. Go to the manufacturers website (Samsung) and click on the drivers and sofware area to download a new copy of the files necessary to run it.

After installing, reconnect your printer to your pc and try printing a test page to see if this has corrected the error.

Jan 16, 2011 | Samsung ML-2570 Laser Printer

3 Answers


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} 01.duplex model memory error
02.LSU trouble
03.shading trouble (black correction
04. shading trouble(white correction)
05. shading trouble
06.Abnormal laser output

Jun 21, 2010 | Sharp AR-5316 Advanced Digital Imager...

1 Answer

Will not copy.

If its giving blank copies there was a ploblem with the laser shutter on these. If so it needs to be taken to authorized Canon repair facility for repair. Maybe still under warranty.

Jan 08, 2009 | Canon NP 7130 Black and White Copier

1 Answer

Xerox m15i

The heat rod is bad in the fuser.
You need to replace the fuser.

Look at this site.

May 28, 2008 | Xerox WorkCentre M15i Laser Printer

Not finding what you are looking for?
Canon NP 7130 Black and White Copier Logo

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts


Level 3 Expert

94198 Answers

old marine
old marine

Level 3 Expert

1316 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides