Question about Sharp Televison & Video

Open Question

Sharp LC-50. FLASHING RED 7 TIMES THEN GOES BLUE WITH NO ??

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ginko
  • 19396 Answers

SOURCE: LC-37AF3X Sharp Aquos KCD TV

If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Posted on May 05, 2009

Ad
dsacco86
  • 1077 Answers

SOURCE: sharp lc-22sv6u won,t power on. no green light.

Sound like the TV is in protection mode. This happens when a part goes bad inside. the TV turns OFF to protect the other parts from being damaged.
Most commonly it's a power supply related issue. A bad capacitor or transformer on the power supply board is to blame.
For a do-it-yourself fixer with electronic experience, a Service Manual is the best for trouble shooting the problem down to the bad part. Normally, you can find it over the internet for less than $20.

Posted on Jul 31, 2009

nikeananth
  • 267 Answers

SOURCE: Sharp LC 37HV4M Flashing red light on screen

hi,

your main board or powersupply is faulty

or

One problem involves the lamp cage being loose. The fix is easy. All you do is remove the lamp and put it back in, making sure everything is tight. I guess they had a problem at the factory, for a while, not tightening the lamp cage. After a certain number of heating cycles, the lamp quits making connection.

thank you for using fixya,rate my answer
vijay

Posted on Oct 05, 2009

satavlad
  • 405 Answers

SOURCE: sharp lc-37sb24u. Flashing Green Light

Backlight invertor is most likely cause of the problem, in rare occasions defective CCFL lamps could cause similar symptoms. Replace defective parts, reset lamp error counter and you good to go.

Posted on Dec 02, 2009

  • 321 Answers

SOURCE: Sharp LCD flashing red light and no picture

yes thats is a common problem for all flat tv not only
sharp ;/ first theres is capacitor in power supply
you probly have few one there blow up and it could bee from the power section of your back light circuit
a good technician can fix that easy
good luck

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power light comes on along with OCP light. No screen or sound. internal switching noises coming from inside the tv


Sharp TV - Flashing OPC & Power Lights - YouTube

? 0:50
https://www.youtube.com/watch?v=BH1OcQ6dIEE
Jul 1, 2011 - Uploaded by Tweetssun
Sharp Aquos TV flashing a OPC & Power Lights in a pattern of 3 flashes, ... Sharp Aquos LC-32D44 - One blink lamp error - Nopicture or sound - Diagnosis ... Repairing Flat Screen TV - Blacked out with blinking red light ...Missing: 32dv22u

Sharp lcd tv power button flashing - HDTV - Streaming Video & TVs ...

www.tomsguide.com/forum/54708-4-sharp-power-button-flashing

Feb 8, 2012 - 7 posts - ‎3 authors
We have owned a Sharp 32" LCD TV for about two years. ... However a quick Bing search shows that the blinking green light usually means a bad power board, which seems ... No picture, no sound, just a black screen and two blinking green ... a cable surge block on the coax where it comes into the house. Sharp lcd tv power button flashing - Digital TV
19 posts
Oct 14, 2012
Sharp hd tv blinking power no picture - Digital TV
2 posts
Jan 7, 2012
More results from www.tomsguide.com
Missing: 32dv22u

Sharp Aquos LC 42DH77: Inverter, Backlight, Power and ...

www.normsweb.com/tektips/42dh77.shtml

Jan 31, 2016 | Sharp LC-32DV22U Widescreen 32-Inch Class...

1 Answer

LCD panel is perfect with no dead pixels, however: When you switch it on, screen comes up briefly, then goes off, with flashing red light. LCD TV Sharp LC-42DH77E model any help very much...


Sounds like a power supply problem - take off the back check voltages coming from power supply if they are good check your inverter board to make sure they are good.

Thanks,
michael

Mar 25, 2011 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

We have a Sharp Aquos LCD TV 42 inch. When I


Call Sharp for warrenty repair.This problem very common in Sharp tv.Picture will come on turn power on/off button few times will work.But still under Wareenty call to Sharp to replaced the main Tuner Signal board.

Jan 15, 2010 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

My SHARP LC-26SH10U PROBLEM. POWERS RED THEN GREEN WHEN I PRESS POWER, THEN SCREEN GOES BLUE AND THE MESSAGE "PLEASE WAIT" APPEARS...AND THATS ALL I GET. I TRIED HOOKING IT TO MY COMPUTER VIA THE USB...


HI, you will need to replace the Digital PCB in this unit. the chip set has become unstable. there is some major circuit damage as well. AKA(PWB UNIT)


Sharp Part Number: A3Y004GDH0 $262.95

Jun 19, 2009 | Sharp LC-26SH10U 26 in. LCD Television

5 Answers

Sharp Aquos wont turn on


this is either a power problem or the screen needs re-gasing

Jan 17, 2009 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

Thomson 40KW611S will not come on


the flashing red light is an error code to assist the service engineer to diagnose the fault .the flashing is normally in 2 groups like 2 flashes then a pause and say 5 flashes

Jan 02, 2009 | Sharp Aquos LC-32G4U 32 in. HD-Ready LCD...

1 Answer

Flashing red light


Same problem with my Sony. Unplugging for 36 hours solved the problem

Oct 05, 2008 | Sharp Aquos LC-37G4U 37 in. HD-Ready LCD...

1 Answer

LC-37AF3X Sharp Aquos KCD TV


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

May 08, 2008 | Sharp Aquos LC-PD50U 50 in. Plasma...

1 Answer

50" Magnavox Plasma


The set needs new inverter boards.Sharp is very aware of this problem.They will fix the set if you push the issue.

Mar 03, 2008 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76054 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Cindy Wells

Level 3 Expert

5909 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...