Question about Malber WD1000 Front Load Washer/Dryer

1 Answer

Drying cycle malfunction

Water pours into the drum when the dry cycle begins, soaking the clothes that have been spun dry.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 383 Answers
Re: drying cycle malfunction

Unplug the dryer and replug back up again.

Put on wash /let it go thru the cycles.

Posted on Nov 27, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Hotpoint WDL520P Washer dryer Filling up with water as it should during the drying phase untill the end of the cycle when it fills up entire drum with water constantly during this cycle it is constant

The other logical point is that it can be related to a faulty output or error from the program controller output. In some cases choosing an alternate program cycle can confirm this case of faulty cycle patterns.

Feb 12, 2013 | Washing Machines

1 Answer

My Hoover 700 LA Top loading washer does not spin dry clothes after the was cycle ? The drum does not spin fast enough for the clothes to dry out as before.

Just got Hoover 700 la manual top loader 2. is taking maximum amount of water on low arrange, and takes an hour on delicates. it also spin dries very strongly, just ruined my clothes..what you would suggest folks..
cheers aysh

Jul 06, 2012 | Washing Machines

1 Answer

During the spin cycle water pours continuously like fill cycle

This problem is commonly attributed to either a water inlet valve leaking by, or a pressure switch malfunction. The following link explains how to diagnose the problem:

I've included parts sources (if required) and how to repair each problem. If you have any questions, please post back and let me know. I hope this information is helpful to you.

Mar 19, 2010 | Washing Machines

1 Answer

I am very unhappy with this machine and sorry I bought it! It uses so little water that sometimes when I take the clothes out after it is finished washing I can see dry spots on the clothes that never even...

How about putting the clothes in and pouring water over them with a jug before the washer starts its program ?.

It could also be that the water level switch is out of tolerance and needs replacing

Most machines have a pre-wash cycle as well

Oct 12, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Maytag top loader on final spin cycle leaves the clothes soaked

how much water is in the bottom of the tub and is it louder than normal if so could be small droplets of water leaking from tub seal if not the pump is restricted by something and req replacement

Aug 20, 2009 | Maytag Washing Machines

2 Answers

Washer-dryer # wm3677HW will not dry,heats up, run, on and on

You're a moron. This unit washes and dries. That's the whole point of it. Perhaps you should do some research before answering the question. the most likely cause is the water lever sensor.

Aug 09, 2009 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

2 Answers

Smell in washer

Vinegar will fix this! Try pouring a quart of white vinegar into the washer, then run a cycle with no clothing in the washer. When the rinse cycle begins, stop the washer. Let it sit for about 30 minutes, then complete the cycle. That should do it! Afterwards, be sure to leave the door open to air dry it.

Oct 27, 2008 | Kenmore Elite 45986 Front Load Washer

4 Answers

LG all in one washer dryer fills with water on the drying cycle

the unit is made to bring water in in the drying cycle ,,the water dont touch the clothes..the water is to take the lint away and to cool the drum,,you must remember that you can was 22 pounds but you can only dry 11 you must dry about half of what you wash..and drying the 11 pounds it will take 3 to 4 hours,,no exhaust...

Sep 21, 2008 | LG WD-3274RHD Front Load Washer / Dryer

1 Answer

Drying cycle ma;function

The problem lies with the water valve at the water entrance area; trace the pipe from where the water comes to dispenser. This should be done after opening up the top ( careful not to touch any part which could give you electric shock or anything) The pipe where the water gushes should be traced back to the inlet area, you will have to change this valve. To see the gush gently open the dispenser drawer.

Nov 27, 2007 | Malber WD1000 Front Load Washer/Dryer

Not finding what you are looking for?
Malber WD1000 Front Load Washer/Dryer Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Malber Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jason Harris
Jason Harris

Level 2 Expert

256 Answers

Are you a Malber Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides