Question about Zanussi Washing Machines

Open Question

How do i lift the filter inside the drum of my zanussi flexi hose washing machine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 183 Answers

SOURCE: replace drum bearing

To complete this repair correctly and to prevent problem re occuring within months you must change the inner drum spider at the same time as the bearing kit, otherwise you are wasting your time, to complete the repair if you have not done one before will take you aprox 1 to 3 hours depending on space available and practicle ability, here goes, remove lid and outer case from machine to do this remove bolts on lower back and two side bolts (under small white covers) remove bolts along top edges both sides on top of macnine, remove cabinet, remove motor, remove hoses, remove heater and thermostat wires, noting location for refitting, remove suspension leg pins and lift outer drum assembly complete fron lower frame, split two halves of outer drum by removing bolts around centre seem, split drum in two, remove drum pully, refit pully bolt and drift inner drum out having put nut back on drum spider thread to avoid flaring shaft, using hammer knock shaft through bearings, then using a chisel or similer object knock out bearings and seal, reverse process refitting new bearins and spider, make sure to replace centre outer drum seal, as these are prone tro leaking I suggest you also seal with a layer of clear silicon, and problems contact me again, not really a job for a novice. Good Luck you will need it. Regards Advisor

Posted on Aug 30, 2007

Ad
  • 43 Answers

SOURCE: zanussi washing machine drum will not go round at all

Tracy
The bearing may have siezed or you have something jammed between the drum and outercasing



Posted on Mar 23, 2008

  • 101 Answers

SOURCE: zanussi washing machine wont spin

check the drain hole when you start the machine if the water is coming back out , if yes that means your dump valve is bad.

Posted on Apr 23, 2008

  • 1 Answer

SOURCE: zanussi washing machine drum will not go round at all

i had a similar problem with a zanussi machine
a cheap bracelet got washed with some clothes and it found its way into the drum housing jamming the drum.

it may have been cheap to fix, but i just got rid of it cos it was 4 years old anyway

i now have a zanussi ZWF1231W just past its 1 wear warranty that has just died completely except for an "on indicator light"
the store inform me that i will have to pay the zanussi engineer a Euro 90 call out charge, plus labour costs, plus parts if needed.

im a little bit disappointed with zanussi to say the least

Posted on Apr 23, 2008

  • 1 Answer

SOURCE: zanussi washing machine filter

Open the panel at the bottom right of the front of the washer. Then pull out the drain hose and pull the plug from its end - this will drain most of the water. Then the filter turns anti-clockwise - if it is too stiff to turn by hand I use an open set of pliers or strong scissors to give more grip (It may be an idea to put a cloth between the pliers/scissors and the filter to offer some protection.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My zanussi washer zwh6160 p stopped working yesterday. It stopped with a load in it. We gad to manually drain it, then git the door open. We cleaned the filter and inlet pipe filter. We switched it on


Considering that machine did not show any error first check that is not activated option "rinse hold" what mean's "stop drum with full of water". I advise you to make a simple test that will show you where the problem is. In the washing machine or somewhere else. Disconnect the drain hose and lift it up to 1m in height and its end hold over the tub or some larger container. Select short drain program and press the start / pause button. If drain hose ejects a solid water stream then is a problem in-house installation of drain water. If does't or poorly drain water then is problem in the washing machine.

Dado

Nov 10, 2014 | Zanussi Washing Machines

2 Answers

Zanussi zwf 1221 will not turn drum, the end light flashes the water goes into the drum and drains out when a program is selected but the drum will not turn at all. You can turn it by hand and it moves...


you need to check the pressure switch inside the washing machine there a small hose connected with the pressure switch to sense that the level of water inside the drum is ok if this hose blocked the machine will not run

Oct 10, 2011 | Zanussi ZWF1430W Front Load Washer

1 Answer

Zanussi Washing Machine - ZWF 14070W1 - Door Lock


Hello,
If there is water still in the drum,try draining it out with the emergency drain hose down by the filter,then take out the filter bung by turning anti-clockwise and pull out to see what has got stuck in the pump.After this is cleared the door should open and the machine should be ready to run again.

Hope this helps.

May 25, 2010 | Zanussi ZWF14070 Front Load Washer

1 Answer

Water not draining from the drum and no filter in evidence


Remove rear panel of washer, locate, and remove large black hose fastened to bottom of drum, remove and clean plastic filter inside hose.
Please rate my solution.
Thanks.

Aug 15, 2009 | Creda W100FW Front Load Washer

1 Answer

Zanussi IZ12 bearings gone & plastic fragments in drum


Probably all parts inside drum is ok.Heating element is the only damageable item and a sensor.Changing bearings you must separate the drum, all screws in middle of drum must out and then bearing and zimmerring can be changed.Jan

Feb 15, 2009 | Zanussi IZ12 Front Load Washer

1 Answer

Coin trapped between rotating drum and casing


Get underneath the machine and remove the big black house coming directly out of the drum,this is held in place with either a screw tie or pinch type tie.
Put the machine back level and see if the coins drop out (they should) or have a feel around inside the drum.
Please make sure machine is unplugged and empty before carrying out this procedure.
Some water will come out of hose.

Nov 19, 2008 | Zanussi ZWF1430W Front Load Washer

1 Answer

Zanussi washing machine


Filter can be clogged, pump can be dead or water outlet clogged.

Apr 11, 2008 | Zanussi ZWF1430W Front Load Washer

1 Answer

Zanussi washing machine drum will not go round at all


i had a similar problem with a zanussi machine
a cheap bracelet got washed with some clothes and it found its way into the drum housing jamming the drum.

it may have been cheap to fix, but i just got rid of it cos it was 4 years old anyway

i now have a zanussi ZWF1231W just past its 1 wear warranty that has just died completely except for an "on indicator light"
the store inform me that i will have to pay the zanussi engineer a Euro 90 call out charge, plus labour costs, plus parts if needed.

im a little bit disappointed with zanussi to say the least

Apr 08, 2008 | Zanussi ZWF1430W Front Load Washer

2 Answers

Cycle


Clean the drain filter ( It says its self cleaning but its not).
On my Hotpoint Aquarius WD440 the procedure is as folows:

1) Drain as best as possible, switch off electrics at socket
2) Remove the plastic panel at the back of the machine
3)Locate the large diameter short black flexi drain hose on the right hand side
4)Slacken the screw on the TOP jubilee clip (The one holding the hose to the drum ) until the rubber hose can slide off
5) The plastic filter is inside the end of the hose. Remove it, disassemble and clean it - then reassemble it remembering to re-insert the ball inside the filter
6) Put the filter back in the hose, there are 2 slots which will locate on two ribs on the drum
7) Refit the hose and re-tighten the jubilee clip.

Dec 26, 2007 | Hotpoint Aquarius WMA42 Front Load Washer

2 Answers

Jetsystem not working


It sound like an clogged inlet water line issue. Check for clean filters and inleat water valve.

Jun 29, 2006 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1479 Answers

jimorris77

Level 3 Expert

411 Answers

Marvin
Marvin

Level 3 Expert

84966 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...