Question about Bench Grinders

Open Question

NEED SWITCH OM MODEL CBG10000L BENCH GRINDER - Bench Grinders

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2712 Answers

SOURCE: Bench Grinders Safety issues

Goggles or safety glasses need to be worn to protect the operator's eyes from the sparks and metal filings that result. Depending on the workpiece and time of exposure, hearing protection may also be required, the dust produced is also potentially hazardous. The toolrest (or workrest) should be mounted slightly below the center of the grinding wheel with less than 3 mm clearance from the wheel. This prevents the work from jamming between the toolrest and the wheel. Grinding wheels designed for steel should not be used for grinding softer metals, like aluminium. The soft metal gets lodged in the pores of the wheel and expand with the heat of grinding. This can dislodge pieces of the grinding wheel. Wire brushes require particular attention for the safety of the operator and bystanders as the metal wires may become dangerous projectiles as they could bind with the object being brushed and so throw it away with great energy. The machine needs to be securely mounted to a pillar or a bench to be used safely and effectively, often with an emergency stop switch or pedal fitted close by the machine, for use in emergencies.

Posted on Aug 27, 2008

Ad
  • 718 Answers

SOURCE: switch and capacitor crapped out on 1/2 hp Sears bench grinder

Replacement should be simple. Just do a one for one hookup with the new part, after you unplug it first.
For a diagram go to;

http://www.searspartsdirect.com/partsdirect/getSubComp.pd?modelNumber=397.1949&productCategoryId=0721000&brandId=0247&modelName=CRAFTSMAN-1%2F2-H.P.-GRINDER&diagramPageId=00001&documentId=00023041&pop=flush

Posted on Mar 28, 2009

  • 384 Answers

SOURCE: NEED ON/OFF SWITCH FOR BUFFALO BENCH GRINDER

You can get a replacement toggle switch at any hardware store look in the electrical department.

Posted on Jun 11, 2009

  • 5603 Answers

SOURCE: bench grinder, 110/220?? wired up properly

LIKELY the capacitor which is usually in the base is bad.

The capacitor shifts the phase angle in one of the two windings which creates a pseudo rotating field to start rotation.

Posted on Nov 16, 2009

  • 172 Answers

SOURCE: Need part numbers to replace eyeshields on Dayton bench grinder

Your grinder is listed on page 3085 of the Grainger catalogue. The part number for the eyeshield is 00281.00 and the number for the lower eyeshield bracket is 00280.00. The right hand upper eyeshield bracket is number 25188.00 and the upper left hand bracket number is 25177.00. All of this can be ordered through Grainger at 1-800-323-0620. Marvin T.

Posted on Jan 13, 2010

Testimonial: "This was very helpful. I have ordered parts from Grainger. Thank You."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need belt for bench grinder belt #lb-12


To find the correct belt you will need to know the Brand and Model Number. Is the number on your old belt or on the grinder? Once you have the correct info you can get parts list by google searing for that. here is what I got just using the bench grinder belt #lb-12.
Just cut and paste the link in a new browser window.
https://www.google.com/search?q=bench+grinder+belt+%23lb-12&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a
Hope this helps..

Nov 04, 2012 | Grinders

1 Answer

I have a Buffalo B-10CB(CH) bench grinder and the on/off switch has broken, it's a push/pull type. What can I replace it with to make it work safely?


You could connect the wires of the switch together inside and bypass the switch. Then I would connect in the power cable a switch rated for 1 hp. You can use surface mount electrical box, with two cable connectors (one for the cable going into the grinder, the other for the cable going to the male cord end of the cable. Install a 120 volt switch inside the box (similar to the light switch in the wall). Make sure that the switch is rated for 1 hp. I would install the switch under the bench, under the grinder.

Joe

Feb 28, 2011 | Baldor 1022w 10" Bench Grinder, 1 Hp,...

1 Answer

Need an on/off switch for a buffalo bench grinder model B-6CB 1/2 hp. 41/2 amp. serial #775713


I had the same problem with a Northern Tools bench grinder. These are made in China and parts are hard to come by. I had enough room after removing the old broken on/off switch to install a single pole 15 amp light switch like you use in your home. I simply installed it horizontally and then put the switch cover on. It works perfectly. If you do not have enough room then look for any 15 amp or larger switch that will fit in the housing. Any on/off switch will work. You could even mount the switch on the bench in a switch housing and run the wires from the grinder to the switch and back if need be. Just be safe and make sure there are no exposed wires. As a last resort you could remove the switch connect the wires, eliminating the switch and use a plug in wall switch such as this. 4147a14.png

Apr 23, 2010 | BUFFALO 10" Bench Grinder

2 Answers

Model 397.19471 need switch but can not find. please help? 8 inch bench grinder


Call the Sears Craftsman help line they will have the parts you need

Apr 02, 2010 | Craftsman 10" Bench Grinder

1 Answer

I need a replacement switch for a craftsman 1/2 HP bench grinder model#397.19441. I have no owners manual or parts list. This grinder is several years old.


this switch is no longer available from Sears, so I suggest making a wiring drawing and taking the switch to a local electrical supply house and try matching it up with a replacement. It seems to be a simple on/off type switch and I would think that you should have no problem. Let me know if you do and give me the information on the switch and I will try some other sites I know.

Dec 28, 2009 | Craftsman Grinders

1 Answer

Craftsman manual for Model 21126 6" grinder


What do you need a manual for? It's a grinder, grind something!!

Sep 09, 2009 | Craftsman 6" Bench Grinder with Lamp

Not finding what you are looking for?
Grinders Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bench Grinders Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2009 Answers

Marvin
Marvin

Level 3 Expert

85104 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you a Bench Grinder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...