Question about Speed Queen Washing Machines

1 Answer

My speed queen has a problem with the inlet of cold water ?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 7 Answers

Change out the water valve. The water valve is what the water hoses are hooked up to on the rear of the machine. This is a pretty easy replacement. The new one goes on like the old one comes off. Turn the water off and disconnect the water hoses from the back of the machine. Sometimes there is one hex head that is removed and the valve tips out for replacement. Depends on the year and model.

Posted on Mar 15, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
TJBENGR
  • 121 Answers

SOURCE: Wash cycle water is not hot for Speed Queen AWS53NW

Possibly a stupid answer..most water supplies at the hose connection have valves...turn off or at least reduce the amount of cold water with valve closed or partially open.

Posted on Apr 21, 2008

  • 142 Answers

SOURCE: SPEED QUEEN WASHING MACHINE LEAKS WATER WHEN IT STARTS WITH WASHU

check hoses and pump area.

Posted on Sep 14, 2009

  • 1 Answer

SOURCE: Replace Water Pump on Speed Queen Washer

did you look at the front panel if you tip the machine to the back and look at the bottom of the panel you will see 2 hex head screws remove them and lift the panel out and slide it down some machines others you have to remove the top

Posted on Jan 13, 2010

  • 2 Answers

SOURCE: I have a Samsung WA13G7Q1 washing machice The

the quection is not complete, when the cold water inlet and hot water inlet both work then what is the problem....

Posted on Apr 27, 2010

heatman101
  • 43501 Answers

SOURCE: cold water inlet not allowing water through it

Hi,
Here is a tip that I wrote about no water coming into the washing machine2_bing.gif...

Washing Machine2_bing.gif Problems No Water
http://www.fixya.com/support/r3880845-washing_machine_problems_no_water

Washing Machine Fix Washing Machine No Water
http://www.fixya.com/support/r3880533-washing_machine_fix_washing_machine_no

heatman101

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Speed Queen top loader, have had to replace the inlet valve 3 times and only owned the machine for 6 months!


Check your water pressure. If it's too high, that's exactly what will happen... Inlet valves will wear out.

Nov 16, 2015 | Speed Queen Washing Machines

1 Answer

Slow hot water fill on speed queen washer


the valve filter is blocked up

turn off the hot water supply and remove the hoze from the machine end valve inlet
in the inlet is a small filter remove it and clean it

if its not too bad perhaps the valves solinoid coil has shorted turns
and wont open fast or fully
check the outlet preasure of hot water from the hoze to a bucket
see it flows fast ..

Apr 03, 2014 | Speed Queen AWS45NW Top Load Washer

1 Answer

My speed quueen modle number ha 3000 w takes about 45 min. to fill the tank


Hi from retired Englishman in SW France,

No speed there, then ;-0)
Sorry, I do not know whether your machine is cold fill only or hot and cold.
If it's both is it just on the wash cycle- when hot water is being fed in or on rinses when cold water is fed in? If it's on both wash and rinse I would have to assume that it is cold fill only.
I would first check that the water supplied to the washer is OK. Turn the tap(s) off and take the hose(s) off. Have a bucket handy (or sink if it is close enough) and turn each tap on in turn to make sure the water flow IS plentiful. If it is, and whilst the hoses are disconnected, check the little filters just inside the washer inlets in case one or other is blocked up.
If all the previous are OK the next suspect is the inlet water control valve (singular- depending again on whether it is just cold fill only) which is malfunctioning and will require a service engineer's visit, sorry ;-0(

Hope I haven't confused you!
Good luck,
John C

Mar 15, 2011 | Speed Queen Washing Machines

1 Answer

Cold water trickles in and fills up slowly


You either have a water pressure/flow problem or the inlet screen in your inlet valve is clogged. Remove the cold water hose and use a bucket to check if you have good pressure and flow. If that is good, look and clean the inlet valve screen for debris. Hope this helps.

Oct 26, 2010 | Speed Queen AWS44NW Top Load Washer

1 Answer

THE MACHINE DONT TAKE OR MIX WATER,ONLY COLD WATER WIL TAKE.


The dual inlet water valve has a failed solenoid on the hot side.
Visit repaircenter.com and enter your full model number to see/order the valve.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Sep 07, 2010 | Speed Queen AWS44NW Top Load Washer

1 Answer

Hot and cold water not coming out very fast.


Turn off the water supply to the washer, and disconnect the inlet hoses, then check the filters in the inlet to the valves.
Also make sure the hoses are not kinked or perished.

Mar 22, 2010 | Speed Queen Washing Machines

1 Answer

Cold water fills slowly


Make sure water valve/tap is fully turned on.
If it is, then turn off, and remove inlet pipe to washer, and check the filter in the hose or the valve, i9f clean, then could be a faulty inlet valve.
Please rate my solution.
Thankyou.

Jan 24, 2010 | Speed Queen Washing Machines

1 Answer

THE TUB OF THE WASHER GETS REALLY LOW WHEN IS FILLED WITH WATER. NOW, ALSO THE WATER DOSENT COME IN WHEN I TURN IT ON


All top suspend tub washers drop down when they fill with water. And they rise again when they have pumped the water out. This is normal.
What is not normal is water not coming in.'

check following:
Water is turned on
Remove inlet hose and run water to see if it is blocked.
Clean the inlet filters.
If you hear a buzz but no water goes in the inlet valve needs replacing.
If yu use only cold water try swapping the cold hose onto the Hot inlet. Then select Warm Wash.
Then only turn on the Cold Tap.
This will allow you to fill the machine and do a wash.
Watch out though when it comes to the Rinse position......some machines only do a cold rinse, and because you have swapped the hose over to hot it will not fill to rinse the clothes. Until you can get a Tech to do the repair you can just use either a bucket to add cold water for the rinse or use the garden hose to fill the tub with cold water for the rinse.
Have yu got all that?

Oct 25, 2009 | Speed Queen AWS75NW Top Load Washer

1 Answer

Cold water flows slowly into the tub when doing wash. checked the screen at the water inlet on the machine and it is clean. water flow on the connecting hose is also ok


If screen and water pressure are ok then the cold water solenoid valve assembly could be partically clogged. The older ones could be taken apart and cleaned. I cannot say if yours can be cleaned.

Jul 07, 2009 | Speed Queen Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

514 people viewed this question

Ask a Question

Usually answered in minutes!

Top Speed Queen Washing Machines Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Paul Bade

Level 3 Expert

1650 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Speed Queen Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...