Question about Linksys A+G WAP55AG 802.11a, 802.11g/b Wireless Access Point

2 Answers

Router i am working with an internet service provider company.we use wireless router. i will like to know how it is configured because some of our client always complained of not browsing.i normally tell them to bye the router and connect directly to their PC.i wiil like to know the configure so i could solve their problem.And if there is a manual to read.Thanks.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Router

I am working with a consultant company.we use wireless acces point.i forgot the user name and password of the the way to reset its,thank's a lot for your help

Posted on Oct 08, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 55 Answers
Re: Router

If you go to start then run, this will bring you to another box. In that box type cmd and then press enter on your keyboard. This will bring you to D (black page with white text) In that box type in ipconfig and press enter on your keyboard. This will show and IP address where it says default gateway. After writing down these numbers type exit in that box and Dos will disappear. Type those number into the address bar when you open up your browser and this will take you to your router page. You can start configuring it from there with the appropriate options given. Remember if you want to protect your router with a password I usually chose WPA PSK. That way you can type in your own password as long as you have at least 8 characters in it. I hope that helps you. Let me know

Posted on Dec 15, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How to change the settings on my dynex g router

You need to configure your router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. or or or If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then set WAN settings as internet service provider settings enable DHCP. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Feb 03, 2011 | Dynex Wireless-G Broadband Router

1 Answer

The installation wizard is not recognizing the router. When plugged into the modem, the internet is fine. No firewalls are blocking the router. Tried different hardware cords, did not fix the problem. ...

Connect your router to computer with ethernet cable then you can access it with following default link. or or or If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then configure wan settings and lan settings enable wireless if you want to use wifi Then save settings and restart router Then connect cable from internet service provider to WAN port of router and connect ethenet lan cable from computer to lan port of router. . Let me know if you need further assistance. Thanks for using FixYa.

Nov 27, 2010 | Dynex Enhanced-G Wireless Broadband Router

1 Answer

Is there any way to use the 2 wire router that at@t provides with road runner internet?

You can actualy use it. Provided that the 2 wire router is a pure router, not a modem/router.

If it is a pure router. Just try to configure the router to act as a router with a DHCP server.

Sep 18, 2010 | 2wire Wireless-G 802.11g ADSL Gateway

1 Answer

Why link led of WAP54G Linksys is not blink if i install cable on LAN Notebook? i try reset this WAP but still not change. I can't login with IP Thanks.

First RESET your router to defaults settings.Press RESET button for 10 seconds it is in back side of router.
Then connect your router to computer with ethernet cable then you can access it with default link
Type user as "admin" and password as "admin" or blank or "password"
Then you can see configuration page of router.
Then configure your router again set WAN settings as your interent service provider.
Enable DHCP if you want iip automatic from router.
CLcik on wireless and enable it .Configure your router as WEP or WAP then add code it is your password to connect internet.
Then save and restart router and computer.
Then connect internet.
Let me know if you need further assistance.
Thanks for using FixYa.

Dec 20, 2009 | Linksys Wireless-G WAP54G 802.11g/b...

1 Answer

Dynex Wireless G Router

check the configuration of the router then re-configur the router it

Feb 26, 2009 | Dynex Wireless-G Broadband Router

1 Answer

No wireless connection

You need to have an Internet Service Provider. You connect the router to a modem from the cable Service Provider or through the phone line for BT. Then you can connect wired or wirelessly to internet through the router.

If you describe your set up in detail and tell me the Internet Service Provider I may be able to help more....

Jan 06, 2009 | Belkin Wireless-G Plus MIMO Router with...

1 Answer

Connecting a wireless router to Tiscalli broadband connection

  1. USB modem is connecting a PC USB port with a DSL phone line: CANNOT be connected to a ROUTER LAN (ethernet NOT USB port).
  2. Wireless ROUTER is NOT a modem and it CANNOT connect the Internet (or WAN) LAN port to any "phone line"
  3. Connect the Router Internet (WAN) port to Modem (you need a LAN MODEM = a modem with a LAN/ETHERNET port)
  4. Be sure your internet is running before strting ROUTER configuration with Router Company CD

Jan 05, 2009 | 3Com 7760 (3CRWE776075US) 802.11a/b/g...

1 Answer

Problem with netgear super g router

Here's sort of a checklist of things to consider:

1. First of all, connect the computer directly to the cable modem. Make certain that your ISP (Comcast) is providing internet service. Modems (DSL, cable) typically have a web page (HTML document output format) interface through which you can connect with your favorite HTTP client (that is, browser), such as MS Internet Explorer or Mozilla Firefox. You can always connect to that if your computer has been given an IP address: you would look for the device you are connected to (modem, router) as the "gateway IP address" (for modems, it might be a 10.0.0.x IP number or something like that; for routers, it might be a private LAN address of 192.168.x.x or 172.16.x.x or something like that). Type in the gateway IP address: if it unsecured, you will see the interface immediately with gettable (status) and settable (configurable) form controls; if it requires authentication, you must enter a username/password combination to gain access to the interface. The default username/passwords are provided in the user guides of the device from the manufacturer.

2. Once you are sure the modem is providing service and that you have configured it properly, then remove the connection to the computer and connect the router. Check that all the lights of the router illuminate properly after startup.

3. Now connect BY ETHERNET (Cat 5 unshieled twisted pair) cable your computer to the one of the slots to the router. We'll go wireless later. Make sure that you are now getting internet service through the router while connected to it with the Ethernet cable. Make sure that you are talking to the router through its web interface. Again, look at your internet settings (find the gateway IP address), and enter that IP address into your browser. You will be challenged for authentication: use the router's default authentication (usually the user name is "admin" and the password is also "admin" or maybe a number sequence like "123456", I don't have your super G model number) and then enter the Interface. Perhaps you need to make special settings for the type of broadband: VCI and VCP values and protocol for the WAN side. You might need to learn these from Comcast's support (by phone or by web site).

Alternatively, rather than us the browser interface to your router, Netgear may provide a CD install disk which contains an application you run to directly manage your router device. It will configure it and also set it up for wireless (see next step).

When you see web pages (such as Google, Yahoo, even Comcast's) through your router, then you are ready to configure the wireless part.

4. While still connected to the router's web page interface in admin user mode, look for the wireless part. You need to set an SSID (don't use the default...create a name you can recognize). This SSID is broadcast to the wireless and you will identify it when opening your computer's wireless adapter. Set an authentication mode as well, so that only you and other can connect to your wireless and no one else (prevents unsecured connections, and turning your wireless into an open "hotspot"). Use WPA or WPA2 (not WEP) if you have it, and you will be given or asked to create a key which is probably a series of numbers and the letters A through F (a long hexadecimal number). Write down the authenticatin type (WPA or WPA2 with AES or TKIP and the key value) and then write this information in for the wireless setup of all computers wishing to connect to the router. You can create this also if Netgear provides an interface (by an CD install disk) for your computer: it may tell you to insert a USB drive to copy information that you would then use to configure all computers that will use the wireless, since it will setup a network configuration that includes the authentication key.

For specific information about how to configure the wireless adapter for router connection, you would need to give the OS you are using (WinXP? Win Vista? MacOS? Linux?)

In future posts, or messages to me, please as a rule provide as much information as possible about ALL devices, namely make AND model/product numbers, since often the experts can check online to see how you can interface with these and configure them.

Aug 11, 2008 | NetGear Super G Wireless Router

2 Answers

Connecting to sky broadband

In general the Wan port of the router gets connected to the modem (box supplied by your internet service provider or ISP) where the computer used to connect and the computer connects to the switch portion of the router which often has 4 or more ports. The router has configuration options that must be set to comply with your internet service providers (ISPs) requirements. These can often be found on his support web site. If you can provide the link to the website I can assist with the search. Otherwise I will need the name of the ISP. If this ISP is cable related like Road Runner I will need the associated cable provider. I will also may need to know the country, city and state in which you are located as some ISPs have geographic differences in equipment. Depending on what that information determines I may also need to know the Manufacturer and Model of the Modem -- probably the box supplied by your ISP. It would also be helpful to know if you got the router used or new. Used routers may have been configured by their previous owner and require additional changes to new routers with factory default settings.

All of the above information may lead to the determination that maybe we must enter a static IP address into the router, maybe we need to provide for PPPoE login for the router, maybe we need to configure the modem to allow the router to perform the PPPoE login, and several other such items. This is probably not a one reply solution.

To provide detailed information concerning that I will need to know the model number of your Belkin Router.

Dec 10, 2007 | Wireless Access Points

Not finding what you are looking for?
Linksys A+G WAP55AG 802.11a, 802.11g/b Wireless Access Point Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Wireless Access Points Experts


Level 3 Expert

18259 Answers

Steven Wander
Steven Wander

Level 3 Expert

574 Answers

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

1869 Answers

Are you a Linksys Wireless Access Point Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides