Washing Machines Logo

Related Topics:

j
jesus Posted on Jun 22, 2018

Good morning I need to disassemble a hamiltom beach model 58148, it has 4 screws and 4 screws, I loose it but it continues without taking off the lid. as I do?

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Sep 19, 2008

SOURCE: Hamilton Beach Meal Maker 33675

Called the toll free number for the company and ordered a replacement cover.

Ad

Anonymous

  • 94 Answers
  • Posted on Nov 27, 2008

SOURCE: acer aspire 3620 lid broke and screen needs to be replaced

If a 'qualified' tech damaged the screen, then it is up to them to replace the screen at their cost.

You could try finding screws slightly bigger and see if they will realign and stop it from being floppy.

Personally I would go back to the tech and complain untill they repair it properly.

Hope this helps a little.

Anonymous

  • 11 Answers
  • Posted on Feb 11, 2009

SOURCE: Moen Villeta 2 handle bathroom faucet, need to disassemble

hold the handle and twist the piece below that doesnt turn, anti-clockwise, it should unsrew and the handle should pull off.

Anonymous

  • 1 Answer
  • Posted on Apr 02, 2009

SOURCE: Replacement Lid-Hamilton Beach #33162 Crock Pot

MarBeck doesn't stock the larger size (10" x 12 1/2") for the 6 qt. slow cookers. Any other suggestions? Not on the Hamilton Beach site either.

Anonymous

  • 3 Answers
  • Posted on Feb 17, 2010

SOURCE: Hamilton Beach Replacement glass lid

try Ebay

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Loose lid

here you go disassembly guide

Download manual

s-ig4loqj0nz5nlta5mtlye45p-4-0.png
1helpful
1answer

How do I take the top off?

To get the top off, you have to pull the front panel off first. To remove the front panel, you need a thin screwdriver (or old butter knife). There are two latches in the crack between the front panel and the top (they are even with the edges of the lid). When you pop those, the front panel comes off. Now the top screws are visible and by removing them, the top will come off. The lid switch needs to be taken loose before the top is removed. There is a good video on youtube.com that shows how to take a GE washer apart. The link to the video is : http://www.youtube.com/watch?v=fjHzxKW4Qw8 . The video shows the disassembly better than I can explain it.
Hope this helps
1helpful
1answer

Washer fills but does not advance to wash cycle without repeatedly opening and closing the lid.

Hello, welcome to FixYa.

Based on your description it sounds like a lid switch problem.

Here`s how you can check it pretty easily...

( this is based on the most common Whirlpool, Estate, Kitchen-Aid, Roper, Kenmore, Inglis topload washer, not neccessarily applicable to ALL...especially those built in the past 1-2yrs. the model number would distinguish if it applies to your particular model )

Lift the lid, if you observe the underside of the lid there will be a plastic "strike" or "actuator" that goes into a hole when the lid is closed.

Check the hole where the actuator goes into the cabinet and insure you can see a gray oval shaped piece. If so take a small screw-driver, pen/pencil or something small enough to fit thru the small hole and try activating the switch by pushing it down ( machine must be in the agitate or spin cycle ). If you don't see it, the switch has likely broken loose and needs to be replaced.

If it start's to function than the switch is not being contacted properly by the actuator on the lid and likely is due to the switch being worn...unless the actuator on the lid is broke, if so there`s the problem.

Make sure the switch is being held in place via the two screws along the side, if they are loose tighten them, if it is broken, it will need to be replaced.

Here`s a helpful link for changing it out,

http://videos.wittysparks.com/id/3098139337

The lid switch will look like this...

40273ed.jpg
Let me know what you find and if I can assist you further.

good luck.

macmarkus :)
2helpful
2answers

Washer fills with water but won't agitate or spin.

Hello, welcome to FixYa.

Based on your description it sounds like a lid switch problem.

Here`s how you can check it pretty easily...

( this is based on the most common Whirlpool, Estate, Kitchen-Aid, Roper, Kenmore, Inglis topload washer, not neccessarily applicable to ALL...especially those built in the past 1-2yrs. the model number would distinguish if it applies to your particular model )

Lift the lid, if you observe the underside of the lid there will be a plastic "strike" or "actuator" that goes into a hole when the lid is closed.

Check the hole where the actuator goes into the cabinet and insure you can see a gray oval shaped piece. If so take a small screw-driver, pen/pencil or something small enough to fit thru the small hole and try activating the switch by pushing it down ( machine must be in the agitate or spin cycle ). If you don't see it, the switch has likely broken loose and needs to be replaced.

If it start's to function than the switch is not being contacted properly by the actuator on the lid and likely is due to the switch being worn...unless the actuator on the lid is broke, if so there`s the problem.

Make sure the switch is being held in place via the two screws along the side, if they are loose tighten them, if it is broken, it will need to be replaced.

Here`s a helpful link for changing it out,

http://videos.wittysparks.com/id/3098139337

The lid switch will look like this...

40273ed.jpg
Let me know what you find and if I can assist you further.

good luck.

macmarkus :)
0helpful
1answer

Need new lid for Hamilton Beach coffee urn model 40515

Hello,

If you go onto the Hamilton Beach website and look at products there is a tab for spare parts.

www.hamiltonbeach.com/coffee-pots-coffeepots.html

Regards
Alan Hood
ami-man
UK
0helpful
1answer

The screws holding the handle on the oven door have come loose. How do you get at the screws to tighten them? It is a Whirlpool range designer model.

Without a model #, I would say you need to take the oven door off and disassemble it to get at the screws holding the door handle. Some models have screws going right through the door to hold the handle on. Best of to call a certified repair company such as Sears.
1helpful
1answer

Need to replace the plastic lid. Anyone know

Call Hamilton Beach customer service. They usually will send the part free, you just pay shipping ($5.00 or less). 1-800-851-8900. I love hamilton beach. They love their customers and stand behind their products. 1-800-851-8900. Also check out hamilton beach.com and look up your product. most regular parts can be ordered on line thru hamilton beach. Good luck to ya.......katherine
0helpful
2answers

Disassemblyan Averatec 7100 how to,...

start popin' screws out and popin the case apart
Not finding what you are looking for?

36 views

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Brad Brown

Level 3 Expert

19187 Answers

Cindy Wells

Level 3 Expert

6688 Answers

john h

Level 3 Expert

29494 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...