HOW TO CHANGE THE INK FROM THE PRINTER EPSON

Hey dude,

In windws XP, Goto start--Printer and faxes on control panel--select the printer driver Epson Stylus CX 2800---right click--select printing prefrences----then under the "maintanance" tab select "Ststus monitor"--there you can get the printer's current status and the cartidge level.Hope it'll help.

Hi,
Here is a link to your users manual, if you lost yours. Page 14 explains how to replace the ink cartridge.

http://files.support.epson.com/pdf/cx6k__/cx6k__pg.pdf

Hope this helps...
Good luck!

f you have just installed a new cartridge and you still see an ink related error message, the cartridge may be incorrectly installed. Follow these steps to make sure the cartridges are correctly installed:

1. Make sure the Stylus CX is turned on.



2. Check the photo viewer screen to determine which cartridge is incorrectly installed. Then do one of the following:



• If printer shows the ink cartridge is expended, press the Start button.



• If the printer shows the cartridge is low on ink, press the Setup/Utilities button. Press the or button to select Press Start to change cartridges. Then press the Start button.



3. Press the Start button again.



4. Lift up the scanner, then open the cartridge cover.

Caution:
Never attempt to open the cartridge cover when the print head is moving. Wait until the cartridges have moved to the replacement position.

Press down all the ink cartridges until they click into place to make sure they are properly seated.

Note:
If a cartridge is properly seated already, you may not hear a click.

Close the ink cartridge cover and press it until it clicks into place.

Close the scanner.

Press the Start button. The Stylus CX charges ink for about one minute and displays Charging Ink on the photo viewer screen until charging is finished.

Caution:
Never turn off the Stylus CX while the Charging Ink message is displayed or you'll waste ink.

Press the Setup/Utilities button to return to the previous mode, if necessary.

I have an Epson printer as well, and the printer has to be on for you to change the ink.

If the error code E-90 appears on your Stylus CX control panel display, the print head may not be able to move back and forth freely.

If the ink cartridge cover is not completely closed, the print head may have trouble moving back and forth. Follow these steps to close the ink cartridge cover:

1. Turn off the Stylus CX.



2. Lift up the scanner.



3. Press down on the ink cartridge cover to make sure it is completely closed.



4. Close the scanner and turn the Stylus CX back on.

Also



If the packing materials are not removed, the print head will be unable to move and the error code E-90 may appear on the control panel display. Follow these steps to remove the packing materials:

1. Turn off the Stylus CX.



2. Lift up the scanner to access the printer area.



3. Remove the tape from the ink cartridge holder.





4. Close the scanner.



5. Turn the Stylus CX back on.

Download your users guide for instructions. 

http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&infoType=Doc&oid=58773&prodoid=56291070

I put alcohol in inside the printer, where you insert the ink cartruges then cleaned with paper towl and it works for me.....

I found this site very helpfull

http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&infoType=FAQ&oid=14082&prodoid=24875245&foid=31693

Epson includes step-by-step instructions on changing the ink cartridges in the Printing Preferences menu:

Click the start button and open the Control Panel.
Right click Printers and select Printing Preferences.
Click the Maintenance tab.
You should see a button that says Ink Cartridge Replacement.

Just follow the instructions and it walks you through it.

Reset waste ink counter use Adjusment Program for Epson Stylus CX 1500. Menu RD Setting, sub Dump ROM Data. Set Protection Mode to 0. Reseter can be found at indoreset.blogspot.com.