Question about Panasonic CT-27HL14 27" TV

1 Answer

Tv switching off

When Tv is turned on ,picture and sound appear but then switch off,

Posted by on

  • Anonymous Feb 16, 2008

    flashes 5 times

  • SBSquareEyes Jul 19, 2008

    I have the same problem as Bobba, the TV works ok for a a short time, and then auto switches to standby. If i turn it back on, it auto switches to standby again within seconds, rendering the set useless. I have painstakingly managed to check the settings in the menu by constantly switching the set on and doing what i can in the few seconds i have, over and over. The settings seem ok, eg, timer is off, sleep is off, install and tuning ok, channel edit ok etc .... can you help whilst i have a shred of hair left please ? SpongeBobSquareEyes

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 934 Answers

This particular unit has a built-in diagnostic. The LED in front will blink for a set number of times following the failure. The blink code is:

1 Flash Power+140
2 Flashes Low B+ D.C
4 Flashes Hi Voltage Hhs
5 Flashes Ic4511
6 Flashes Ic4518
8 Flashes Audio Amp

Can you possible tell how many flashes there are following the instant shutdown?

Bill

Posted on Nov 25, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sanyo dp50747


sounds like a mainboard problem

Jan 31, 2013 | Sanyo DP50747 50 in. Plasma TV

3 Answers

Wont put out a picture or make sound when turned


turn off your xbox and switch the switch on the video/ audio chord and turn it back on. or just get a new audio/video cord

Nov 04, 2009 | Microsoft Xbox 360 Console

1 Answer

I just replaced lamp in hln5065w but still not getting a picture when i turn on just middle light blinking....when i look at the back of tv lamp doesn't appear to be coming on but checked connection and...


- make sure your cover is placed back ON or put a tape over switch cover.
- Are you getting any sound? if so, check your connection on the ballast.
- You should have one small green light ON from the back when TV is OFF. When you turn ON the TV manually or by remote, You should hear one click and then the color wheel starts turning, then the large light bulb should start to turn ON, then a few seconds later the sound and picture appears. If the remote or manual functiomn does not do anything,m then your DIGITAL board is gone. If you get the TV to turn ON and get something, there is a problem else where, probably ballast board near switch cover bottom right.

Robge

Oct 17, 2009 | Samsung HLN5065W 50" Rear Projection...

1 Answer

Only the sound comes in my tv no picture at all . When i switch it on the sound comes over but no pictures.any suggestions please?


you have to turn the screen control up a bit.there are 2 conrols on the flyback transformer,top one is focas bottom one is screen,turn it up 1/8 turn turn set off then on.repeat this until picture appears(if you turn it up too much picture will be to brite with lines and will shut off) if it shuts off just turn contron down a bit then restart it.

Sep 24, 2009 | Sony FD Trinitron WEGA KV-32FS120 32" TV

2 Answers

PS3 IS ON, BUT NO PICTURE OR SOUND


no problem just turn system to standby mode and hold power on switch on system itself down for 10sec this will reset factory settings and picture should appear

Jan 06, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

No Picture but have sound


OK I got my first TV, first to repair myself that is, and I have no training at all but am kind of a tech dork wannabe. So I checked and I have sound but no signal through the TV tuner, so I hooked up my Zenith VCR to aux 1 and sound with signal appeared, the VCR tuner still works :) so I am leaning toward the TV tuner. It is visibly damaged, and I'm hoping it is as simple as a broken connection. I also noticed a vertical flash and pattern of horizontal lines when it is turned off (white). sooooo I push on.... help!!!!!!!!!!!!! :>}

May 02, 2008 | Televison & Video

2 Answers

Samsung TSL3293HF HDTV - TV in Stale State-No picture or audio


I HAD A REPAIR GUY OUT TODAY AND HE SAID IT WAS THE POWER MODULE. I HAVE NOT GOT A PRICE FOR THE PART OR REPAIR YET.

JASONCBFAN

Feb 01, 2008 | Samsung TSL3293HF 32" TV

5 Answers

No picture but has sound


My LG TV
switch on no picture but short period of sound then nothing

Jan 20, 2008 | Sony KP-51HW40 51" Rear Projection...

1 Answer

Sound but No Picture


Perhaps your remote is set to video recorder?  Try that first, and if no response, try calling up a menu on your TV and look for the Picture Settings.
Good Luck.

Nov 03, 2007 | LG 37LP1D 37 in. LCD Television

Not finding what you are looking for?
Panasonic CT-27HL14 27" TV Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5342 Answers

Demonic-2011
Demonic-2011

Level 3 Expert

508 Answers

The Knight
The Knight

Level 3 Expert

75169 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...