Question about Bosch SHU5315UC Dishwasher

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to "CL" in the digitial window. Thanks for your help

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Posted on Aug 13, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Rotu
  • 175 Answers

SOURCE: stuck on last minute

I have seen a lot of these dishwashers burn out the control board, and usually the symptom is the timer not working or inability to complete a cycle. Most of the ones I have seen, you can remove the control board assembly and its pretty obvious where its burnt. If you can do the repair yourself, the board is about $150. Hope this helps!

Posted on Oct 26, 2006

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore 13789 draining/cleaning issues


Check your wash arms - make sure the holes or nozzels are clear (not blocked), and make sure they are free to turn. Make sure you are not over-loading the dishwasher or placing large plates or pans in front of the soap dispenser. Next is to check to see if enough water is going into the DishWasher (DW). This varies with different models, so it's hard to tell you how much is enough. Next thing to check is to make sure the heater is working to heat the water during the wash cycle. (Listen for the soap dish to open, then open the door 10 or 15 minutes later and see if the water is hot.) If your dishwasher has a removable filter, you need to take that out and clean it at least once a month. And finally, if your dishwasher is all encrusted with calcium and hard-water deposits, you probably need to run a dishwasher cleaner in the machine. (Use Dishwasher Magic, or Finish Corp's Dishwasher cleaner, or Glisten, or even Lemi-Shine detergent-booster powder or their dishwasher cleaner.
Hope this helps!

Dec 31, 2012 | Kenmore 13789 / 13782 Dishwasher

2 Answers

TECNIK TDK 795 FAULT


is there the power supply still to the washer??

Mar 01, 2008 | Tecnik 24 in. TKD795/3 Built-in Dishwasher

1 Answer

Our Neff S5454x1/21 dishwasher has occasionally stopped/stuck


Looks like the heater unit has packed up.

I cannot seem to find the actual model you have anywhere on the internet. But I am assuming you connect the dishwasher to cold water inlet and it is meant to have a heater.

Are you in UK or Europe. Bosch also makes parts for the NEFF dishwasher but I am not able to find spare parts for your exact model.

Please post a comment.

Jun 05, 2010 | Neff 24 in. S5453X1 Built-in Dishwasher

1 Answer

Poor washing quality and water left in the filters ets


My friend, that siemans is a night mare to open. Just done one recently. Anyway, looking at it simply, i would suggest you check the inlet water filter. if water is slow to come in it will cause this problem. Remoe the water pipe from the solonoid and look for sieve. clean it well retry.

Sep 21, 2009 | Siemens 24 in. SE25A266 ExtraKlasse...

2 Answers

Bsoch dishwasher runs long and displays 1 minute left on timer


sounds like a bad solder connection on the heater relay of your control unit. more than likely you will need a new control unit. part number 266746

Feb 22, 2009 | Bosch 24 in. SHU53 Built-in Dishwasher

1 Answer

Whirlpool gold dishwasher gets stuck at 53 minutes left for an hour


Try "resetting" the control board by running the diagnostic cycle. The cycle completes in 15 minutes. 
The details are in the service manual. The manual can be found hidden behind the tow plate (at the very bottom front of the washer).
The diagnostic cycle may tell you the problem. It also helps clear up some of the software gltiches. 
It is easy to run the diagnostic cycle.
Just the buttons in the following sequence. The sequence should be complete within 6 sec. 
heated dry -> Normal -> heated dry -> Normal
This will trigger diagnostic cycle of 19 intervals. Pay special attention to the intervals 18, 17, 9, 6, 4.
Interval 18 - displays your controller module number (should be letter 'd' followed by number 0 or 1 or 2 or something. Note that down for future reference.
Interval 17 displays 'software generation number' Note that down for future reference.
Then wait until you reach interval 9.  --- clean LED turns on - then an open or shorted thermister is detected.
-- Sanitized LED turns on - then the washer detected greater than 100 deg F temperature
Interval 7
-- Soaking/sensing LED should NOT come on (unless food soil is present).
Interval 4 -- Soaking/sensing LED should come on


Let the cycle complete and then try running the normal wash. Hopefully the possible glitches are cleared by now and you should have no problem. 
If this doesn't work, time to call the expert tech. 

Nov 08, 2008 | Whirlpool Gold 24 in. Built-In Dishwasher...

2 Answers

SHU43 running constantly


Intrrnal leak into base of appliance will make drain pump run constantly.
If appliance fills then dumps water with drain punp then keeps filling/draining sequence then the flow meter could de faulty.
Call in engineer.
Paul Winn Appliance Services (Cumbria)

Apr 02, 2008 | Bosch 24 in. SHU43 Built-in Dishwasher

2 Answers

Electronic controls don't count down properly


you have to replaced the main control resoldering wont fix it because the relay itself has gone bad replacing the board will solve the problem

Nov 20, 2007 | Bosch SHU5315UC Dishwasher

1 Answer

Rinse Cycle Finishes but Drying Cycle Doesn't Start


Does this unit run for hours with 1 min remaining? if so you need to replace the controll board. I have soldered some with sucess but it "Should be replaced" You also need to make sure you have just dry liquid in the unit and "Don't use soap tabs" 1 -3 tsp of soap that is all. If you are good with mech work I can walk you through the way to check ths unit out to tell what the problem is.....

Apr 14, 2007 | Bosch 24 in. SGI57M05SS Built-in...

1 Answer

Stuck on last minute


I have seen a lot of these dishwashers burn out the control board, and usually the symptom is the timer not working or inability to complete a cycle. Most of the ones I have seen, you can remove the control board assembly and its pretty obvious where its burnt. If you can do the repair yourself, the board is about $150. Hope this helps!

Oct 26, 2006 | Bosch 24 in. SHU5305UC Built-in Dishwasher

Not finding what you are looking for?
Bosch SHU5315UC Dishwasher Logo

2,084 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...