Question about Kenmore 98702 Stacked Washer/Dryer

1 Answer

Indesit w113 fills with water and then dial just spins to number 9

Hi, have an indesit w113. when i set it to a wash programme the machine fills with water and then the programme dial just spins to number 9 and nothing seems to happen. Prior to this fault the machine used to take a very long time to complete a wash cycle.

Posted by on

1 Answer

Re: indesit w113 fills with water and then dial just spins to number 9 - Kenmore 98702 Stacked Washer/Dryer Washing Machines

Test the element

Posted on Jan 15, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Flashing lights

There is a Light Flashing on my Indesit Washing Machine

Many of our newer Indesit Washing Machines have a series of indicator lights, which flash to indicate a possible fault on your installation or simply to let you know a problem occurred whilst you were away from your Indesit Washing Machine.

Pre wash light flashing
Indicates a failure of your Indesit Washing Machine to fill correctly. Check your fill hoses for a blockage, a leak, a kink or to make sure that they are turned on.

Wash light flashing
Indicates that your programme dial has been moved from its original position. Simply returning the wash dial to its original position will restore the light to its original status.

Spin light flashing
Indicates that the Indesit Washing Machine has considered the wash load to be excessively un-balanced. Open up the door of the Indesit Washing Machine, re-distribute the garments and retry the spin to resolve this.

End light flashing
Indicates that the Indesit Washing Machine has reached the end of a wash programme.

Wash, rinse and spin lights all lit at the same time would indicate a possible blockage in your under sink wastes system. Check out the additional informationin our 'My Indesit Washing Machine Will Not Empty'

Aug 22, 2012 | Indesit Washing Machines

1 Answer

Iwde12 indesit, not selecting programmes not releasing water, not drying

Hi, I have an indesit IWDE12, I programme the washer which then starts to spin with no water, after 2-3 mins the rinse light, the clock light and the door lock light start to flash and tha washing stops. Does anyone know what this problem could be?

Jun 15, 2010 | Indesit W 123 Front Load Washer

1 Answer

Programmer sticks before the spin cycle (number 5 and 9) on my beko washing machine also if you change programmes the programmer jumps round

Prog jumps as it will carry out 1st command selected unless reset.the sticking could be a faulty water solonoid valve if this happens say during softner fill although could also be the timer /programmer at fault

Apr 03, 2010 | Washing Machines

1 Answer

Machine wont stop washing on programme 9! went for days. Had the error lights flashing but that stopped.

If you select a rinse and spin programme and it completes the cycle, then I would say that the heater element is probably faulty, because the programme will not advance until the water has reached the correct temperature.
If it does not complete the rinse and spin cycle, then it is likely to be the control module that is the problem.

Feb 09, 2010 | Indesit W 123 Front Load Washer

1 Answer

Indesit washing machine not spinning - fault code timer and dor lock light flashing

my indesit washer/dryer wd12x programme dial goes all the way when it reaches spinning

May 30, 2009 | Indesit W 123 Front Load Washer

1 Answer

Washing machine will not drain


May 29, 2009 | Indesit W 123 Front Load Washer

1 Answer

Indesit w113 and w1101 wasing machines dial clicking round

This type of fault is usually associated with a faulty programmer. if you have a reset point, then try to reset it, if no reset, then programmer is faulty.
Please rate my solution.

May 11, 2009 | Washing Machines

1 Answer

Washing machine wont do anything

rotating timer knob indicates that there is a fault, obviously, so its a case of going through a checklist, based on info given, check in this order, outlet pump, for open circuit, then heater element for open circuit, then maybe the water valves, you have given little information for me to go on as an engineer, please understand, the more you say the more detail we can give ..... ok cheers with looking for the fault, best of luck and work safe

Dec 21, 2007 | Indesit W 123 Front Load Washer

1 Answer

Indesit Washing Machine not proceedding with the cycle programme after filling with water.

Cant understand how the machine will revolve on the 'spin cycle' & yet you can hear the motor on the 'wash cycle' but yet it doesnt revolve!!
Nomally if the water fills, & the tub revolves without the programmer advancing, its because the heater is not working. ie faulty thermostat, heat element, or maybe a wire burned off in the 'heater circuit'. Check if you have 240 volts at both ends of the heat element, with a meter or 240 volt bulb
                         !! BE CAREFUL OF 240VOLTS!!

Oct 29, 2007 | Indesit W 123 Front Load Washer

2 Answers

Indesit w113 washing machine

check heating element (rear of drum at the bottom) for open circuit, replace if needed, occasionally the timer will start to click round continuously, indicating the machine has a fault, the machine shuts down waiting for the water to heat up, elements available at most appliance shops but you may need to order specially?

Sep 01, 2007 | Washing Machines

Not finding what you are looking for?
Kenmore 98702 Stacked Washer/Dryer Logo

Related Topics:

405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides