How do you replace the rollers on a Talaris EV8626

Question moved from Vacuum Cleaner category.

Take it to a local suitcase repair shop. It often involves riveting.

https://www.google.com/search?q=suitcase+repair+near+me

Wheels are available on Amazon.

https://www.google.com/search?q=suitcase+rollers

..

Maybe you can try With the clutch to control, hope can help you.
Motor Part Store Motor Parts Wholesale

Let me set the record straight. Brandt invented the 8672, one of the best machines of all time. Unfortunately it was way over priced. Brandt was in business for over 110 years and then sold out to the employees of the company who then sold out to the DeLaRue company in England. DeLaRue then sold out to Talaris. And, finally, Talaris sold out to Glory two years ago. However, the 8672 stopped production before Glory became the owner. All the above took place over 15 year period. Got all that!!
Now back to your question. What kind of manual do you need? I would need to know the full model and serial number for the correct manual.
If your counter say Brandt on it, that is very old. The newest version has the name Talaris on it. Spare parts can be had, but are very rare and somewhat expensive since the machine is no longer made. Here is a picture of a 8672. Good luck.....

3 inches is approximately 70 or so mm so i would say you have a bad drum on your toner

27mm - charge roller - Replace toner
75mm - Photosensitive Drum - Replace toner
34mm - Developing Roller - Replace toner
39mm - Transfer roller - clean/replace transfer roller
57mm - Fuser Film - Replace Fuser
56mm - Pressure Roller - Replace Fuser

This should help. Good luck !

Cassette (Tray 2) paper pickup and feed rollers

To remove the paper pickup and feed rollers

1 Remove the cassette.

2 Locate the two rollers on the bottom of the paper pickup unit (above the cassette). The pickup

roller is the smaller roller, and the feed roller is the larger roller.

3 Pinch the tab on the end of the cassette pickup roller (callout 1), and pull the roller out.

4 Pinch the tab on the end of the cassette feed roller (callout 2), and pull the roller out.

Figure 6-24 Removing the cassette pickup and feed rollers

Note Always replace the cassette pickup roller and the cassette feed rollers at the same time. Also replace
the separation roller (located in the paper cassette) when replacing these rollers

Unclear on problem but Mircosoft gives this help here.
Error codes in Device Manager in Windows

Looking from the back of the 8650 counter with the lid open, there is a safety switch on the left side. It is either not pressed in when the lid is closed or it is broken. To test, take the two wires from that switch and connect them together. That will by pass the switch and allow the machine to work. Good luck.

INK ROLLER REPLACEMENT

If printing is blurry even when the ink roller is in the proper
position, replace the roller.
Ink roller: Type EA-732R

WARNING
APPLYING INK TO WORN INK ROLLER OR USE OF
UNAPPROVED INK ROLLER MAY CAUSE SERIOUS
DAMAGE TO PRINTER.

1) Turn the power off.
2) Remove the printer cover. (Fig. 1)
3) Remove the ink roller by turning it counterclockwise and
pulling it upward. (Fig. 2)
4) Install the new ink roller and press it in the correct position.
Make sure that the ink roller is securely in place. (Fig. 3)
5) Put back the printer cover.

Hi Ranji,
Thank you for contacting Fixya.
The life span of the Pick roller is about 200,000 sheets or one year. Use Abrasion counter on the operator panel to estimate when the Pick rollers need replacement. The life span may be decreased by as much as half when carbonless sheets are frequently read. To replace Pick Rollers, please follow the steps provided below:
a. Remove Guide AASY. b. To remove the Pick rollers, turn the stopper counterclockwise. c. To remove the Pick roller 1, move the Pick roller 1 toward the left then lift it. d. Right after removing the Pick roller 1, remove the Pick roller 2 with the same way. e. To attach the new Pick rollers, place the Pick roller 1 from right above the groove for the Pick roller 1. Put the shaft of the Pick roller 1 into the groove. Then, slide the Pick roller 1 toward the right side. A Pick roller 1 has the groove in its rubber. Make sure that the bushing is securely fixed to the grooves. f. Attach the Pick roller 2, then slide the Pick roller 2 to the right. Make sure that the bushing is securely fixed to the grooves. g. Turn the stopper clockwise to secure the Pick rollers.
Hope the above information is helpful.
regards,
TechSatya