Question about Husqvarna Garden

1 Answer

Need diagram to feed belt - Husqvarna Garden

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 133 Answers

Make sure you have the right belt and then it should be fairly easy to route the belt if you put the back of the belt (flat side) up against the larger in height idler pulleys and the smaller (v) in the smaller pulleys. The belt should be snug when on properly.

Posted on Aug 01, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Belt diagram john deere sabre 1338 GXABRF

the cheap john deeres are notorius for belt jump. Have to look at idler pulley while engaged in normal cutting height and see if it rides the upper edge of the idlers. I have had to bend up the idler arm so it runs a truer line into the pulley/idler so it doesnt creep over the edges.

Aug 30, 2014 | John Deere Garden

1 Answer

Serpentine belt broke and cannt figure out how it goes back on

there should be a belt tensioner you can loosen off. loosen it, feed your belt through then tighten up the tensioner. note - get a diagram off how to feed your belt through all the wheels.

Jan 09, 2013 | 1998 Oldsmobile Regency

1 Answer

Bekel 919 belt routing diagram

go to

Jan 30, 2012 | Berkel 827E Gravity Feed Deli Meat Slicer

1 Answer

The belt on the enging that's on the passenger side has completely worn away, and it broke on the way home. The car managed to make it home, but I had to drive real slow, and of course the temperature...

the belt is a pretty easy fix, and the part isn't that much either, However driving it with no belt could be very costly,, when you go to the parts store to get the new belt, just ask them for a print out of the diagram for the belt,, if you need more assistance Just reply to this feed

Aug 29, 2011 | 1998 Volkswagen Jetta

1 Answer

I need a serpentine belt diagram for my 1993 toyota tercel.. i can't find where to loosen the pulleys so that i can take off the belts to replace it you can find ther diagram on that link, if your just trying to figure out how to loosen the belts,, depending on which motor you have ,, you can loosen either the ac unit or the alternator to free up the belts, if you respond to this feed and tellme which motor you have I'll locate which one for your car

Aug 23, 2011 | 1993 Toyota Tercel

1 Answer

Need the diagram on the main belt with air... it sleeped off when i was putting on the alternater go to that page and look up your motor, grab the diagram picture number it lists , scroll to the bottom half of that page, and it will show you the routing, I couldn't get it for you because you didn't list which motor you have,, if you need more help just reply to this feed,, Please take a moment to rate my reply

Jul 19, 2011 | 1999 Chevrolet Cavalier

1 Answer

How does the belt look on a maytag neptune need diagram

the belt should be on the center of the drum,
collect the loop on the botom
and feed the loop under and through the idler pully
take the loop and lift the idler pully, put the loop on the motor and release the idler
you should ba all set

Oct 17, 2009 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

I have a OLD Craftsman lawn tractor 36'' Drive belt diagram ?

go to click on parts and enter your mod#

Apr 19, 2009 | Garden

1 Answer

I need a belt feed diagram/maybe owners manual for my dryer

do you have the brand and model number?

Apr 08, 2009 | Dryers

Not finding what you are looking for?
Garden Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

Phil Walker
Phil Walker

Level 3 Expert

608 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides