Question about Sanyo PLC XU48 Multimedia Projector

1 Answer

Sanyo PLC XU48 problem starting

Have to power on and off few times before the projector will start up.

power indicator lights fan turns on but nothing. I had to replace the lamp could that cause it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 115 Answers
Re: Sanyo PLC XU48 problem starting

Service and reinstall main PCB connectors and cables including sensors. check the lamp condition also.


Posted on Nov 27, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Lights flashing

Replace the lamp. The lights flashing will also indicate what is wrong. Watch how they flash. Go to the manufacturers website and they way they are flashing indicates what is wrong (ex. 3 quick flashes, long continuous flashes...etc.) When you change the lamp reset the lamp counter in the menu and clean or replace the dust filters as well.

Jan 11, 2014 | Sanyo PLC-XP200L Projector

1 Answer

Sanyo plc-xt16 Projector After the projector is turned on and the countdown finishes on initial start up the projector shuts itself off within 5 seconds. The fan runs for 1 minute and then the projector...

It sounds like the lamp is going.
Do you know how many hours of use are reported on the lamp?

Many times these projectors have circuitry to shutdown when they suspect the lamp is near the end of life. Lamp hours vary and usually will go up to and even beyond expectancy, but there is occasions you can receive a bad lamp and have it blow in a matter of hours...not common but it does occur.

I hope this helps,

Mar 09, 2011 | Sanyo PLC-XT16 Multimedia Projector

1 Answer

How do I replace the ballast on my Sanyo PLC XU48? Where do I get a replacement ballast?



Kindly try above link to know where you purchase various Sanyo parts for your projector.

Thank you.

Jul 29, 2010 | Sanyo PLC XU48 Multimedia Projector

1 Answer

Sanyo PLC XU48 Need to know the lamp hours!

press and hold down the power button for about 20 seconds. The info will show in the top right of the screen.


May 25, 2010 | Sanyo PLC XU48 Multimedia Projector

1 Answer

Lamp goes out after 10-15 seconds

Recently had a similar issue.
When I took the lamp out (Let it cool for awhile first), there was dust all over one side preventing air from the fans from cooling the lamp, so it shut itself off after getting too hot.

Apr 27, 2009 | Sanyo PLC XU48 Multimedia Projector

1 Answer

I have a Sanyo PLC xu38 projector broken receptical.

you should find a new db15 female connector, and install on to pcb, this required good knowledge of soldering...

Apr 20, 2009 | Sanyo PLC XU48 Multimedia Projector

1 Answer

Sanyo PLC-XU47 seems to power cycle

Welcome to resolve the problem if you please say what are the solution to me the same problem

Jun 07, 2008 | Sanyo PLC XU35 Multimedia Projector

Not finding what you are looking for?
Sanyo PLC XU48 Multimedia Projector Logo

Related Topics:

639 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Multimedia Projectors Experts


Level 3 Expert

2236 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

66352 Answers

Are you a Sanyo Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides