Question about Washing Machines

2 Answers

I have a roper washer model #rab5232ew1 first how old is it?? the problem is when it start the cycle the tub fills up with water and it starts turning and washing the clothes and half way thru the washing phrase it just stops and nothing has been touch, also it is not over filled with clothes seems to me the timing cycle dial is shot to empty the tub i have to un plug the washer and play with the dial with the different settings to rinse and then spin my question is what is the cost of the dial thanks

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 37 Answers

The part you refer to is called the timer - find it here www.repairclinic.com

Posted on Jul 31, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,000 Answers

The timer does appear to be available,
Timer
Part Number: AP3019192 made by WHIRLPOOL
COST: $102.52

I could not find any info that would indicate the age of the washer.
Regards,

Posted on Jul 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Roper heavy duty 8 cycle 2 speed combination washer does not fill up on rinse cycle


when in rinse washers use just cold water so clothes don't wrinkle,try this,set the washer to just cold,start it and see if it fills or fills slowly if so you have a bad water valve on washer or no cold water going to washer.

Dec 04, 2017 | Roper Washing Machines

1 Answer

Roper washer new will not fill with warm water on rinse cycle it fills and spins


if its only a new machine make sure transport bolts have been removed

Apr 09, 2014 | Roper Washing Machines

1 Answer

I want to keep the water in my Roper top load washer overnight so it will soak the load of whites I have started but the machine drains.


You should be able to select a soak cycle without having to turn off the water supply, but it may time out eventually and drain the tub. This p[events oversoaking the clothes

Oct 13, 2012 | Roper RAS8445KQ Top Load Washer

1 Answer

My Roper washer will only work on the spin cycle. It will not fill or work on any other setting. The fill hoses are clear of debris and there is no kink in the drain hose. What do I check next?


The indication you state is consistant with the washer sensing water in the tub. If there is no water in the tub, then it would be the tub sensor. If there is water in the tub, and the spin cycle doesn't get it out, then I would look at the pump or the control board.

Jun 08, 2011 | Roper Washing Machines

1 Answer

I have a GE toploader washer. The model # is WBSR1060T (VVSRV1040V, & YVSR1040V were also on the washer too) the washer keeps filling to the max setting no mater what the water level is set on, also...


Remove the front panel of the washer by using a putty knife to release the retaining clips, located in the seam between the front panel and the washer's top, about 2 inches in from each side. With an empty wash tub, remove the small hose on the left side of the outer tub and clean out the inside of the hose. Replace the hose. Test.

Mar 15, 2011 | Washing Machines

1 Answer

The washer's springs configuration


They are hooked from the bottom frame to the carriage that holds the tub. Not sure of the model you have but most Whirlpool (They make kenmore, roper, magic chef and others) There is a ring around the top of the outer tub that is filled with water from the factory. Make sure it still has water inside. It acts as a damper helping to balanced the tub also.

Oct 13, 2009 | Roper Washing Machines

2 Answers

Water runs contiuously... tub never fills...cycle doesn't start.


Hi, You need to reset the drain hose. It needs to be over the water level in the machine. If you have it in a sump pump, it needs to be out of the water in the sump. If I can help you further, please let me know

Thanks
Vic

May 16, 2009 | Roper RTW4100SQ Top Load Washer

2 Answers

Washer won't stop filling


if you can turn the washer off while it is still filling. and the water continues to enter the machine you have a bad inlet valve.
Do me a favor turn the washer to fill, with the washer still running unplug from the wall. If the water is still entering the unit you have a bad inlet valve

Jan 05, 2009 | Roper RAS8445KQ Top Load Washer

1 Answer

Washing machine does not stop filling


Does the machine start working normally after turning the wash cycle manually ?

Feb 15, 2007 | Roper RAS8445KQ Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

80608 Answers

Brad Brown

Level 3 Expert

17328 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...