Question about Raymarine C80 GPS Receiver

Open Question

How to use Loran on C80

Can seem to find the loran on my c80...have looked everywhere. Have the Navionics Gold....Thanks so much

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
hydetech
  • 113 Answers

SOURCE: converting loran numbers to GPS.

When you enter the Loran coordinates, they should only be 6 digits with one decial point ie: 12345.6

On the chart the coordinates may be shown with a prefix such as as 9960-W14123.4. The prefix (9960-W) is not entered on the conversion screen. It has to be set up in the position format set up page in your GPS prior to doing the conversion.

For example on my Garmin 76CS, I go into the setup menu and select position format.
I scroll down through the list of formats until I find "LORAN TD" and press "enter".
In this screen I enter the master chain number, which is 9960 for my region in New England.
I also have to enter the "slave" stations which are designated as V,W,X,Y, or Z. For example, in my region, the "W" slave station always starts with the number 14 (ie:14123.4) and the "Y" slave station always starts with 44 (ie: 44123.4).
When I am in the conversion screen, I don't have to enter 9960-W because the GPS is already formatted for that.

You should also note that a LORAN TD converted to Lat/Lon will not be as accurate because there is some mathmatical error in the conversion equation.

Posted on Jul 21, 2008

Ad
  • 14 Answers

SOURCE: Whenin use, my c80 emits a series of 3 loud beeps

You have triggered MOB (man over board) press and hold the MOB button in for 30 seconds.

Posted on Sep 23, 2009

  • 43 Answers

SOURCE: takes sometimes upto an hour to get fix 120/ c80

look after your software version it shoud be 4.29 after this make a reset (you will lost all the data like waypoints routs and other)

Posted on Oct 13, 2009

  • 43 Answers

SOURCE: GPS antenna

If your old antena is a Seatalk or NMEA antena you can use it for your C80
If you GPS antenna is older than five year change it.

Posted on Oct 31, 2009

  • 5 Answers

SOURCE: I live in Key West. I have a loran no. that was

Those loran numbers I see in your post are like your corandenses. Not sure if I spelled these words right. Its longitude and latitude. A suggestion for you is to start all over with your unit. In your tools section, you can delete and then start all over. If yours has a place to put those corandenses in, do so at that time. Hope this helps. Blessings.

JB
Redding, CA

Posted on Dec 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't update software


Hi
As you have isssues with boyh software update and chart I would put my bet on the cartridge reader, it could be a loos or broken pin. Use a penlight or good light and inspect the pins in the reader for damages and check that there is no pin stuck in the Navionics cartridge. If no pin is missing it may just be loose, can be fixed by opening the plotter inspect the reader from behind and use a glue gun to resecure the pin(s). In worst case you will have to replcae the reader (affordable).

Apr 02, 2014 | Raymarine C80 GPS Receiver

1 Answer

What is the connection path from Garmin 72 to raymarine c80, using NMEA 1083


I'm taking this as you want to send the gps information to your C80 not receive from the C80? If this is the case the brown wire on the garmin is the nmea data out +. The Black wire is considered nmea out neg (-) of the garmin. So hook the garmin brown to the white on the raymarine. Hook the black from the garmin to the green on the raymarine. That means you are outputting lat/long info to the raymarine from the garmin.

Jan 14, 2012 | Raymarine C80 GPS Receiver

1 Answer

I am buying a boat with a 2005 Raymarine c80. i need maps for alabama lakes and the gulf cost of Alabama and Fl


Call Mid-shore Electronics and speak to Ann. She may be able to help you out and have the chart shipped to you from Navionics. The number there is 410-228-7335.

Jan 30, 2010 | Raymarine C80 GPS Receiver

2 Answers

I need a driver


"http://mac.brothersoft.com/epson-stylus-c80-driver-x-download.html"

that is the link to the driver for your pinter rate this solution

Dec 19, 2009 | Apple Epson Stylus C80 InkJet Printer

1 Answer

I live in Key West. I have a loran no. that was


Those loran numbers I see in your post are like your corandenses. Not sure if I spelled these words right. Its longitude and latitude. A suggestion for you is to start all over with your unit. In your tools section, you can delete and then start all over. If yours has a place to put those corandenses in, do so at that time. Hope this helps. Blessings.

JB
Redding, CA

Dec 07, 2009 | Garmin nuvi 250W GPS Receiver

1 Answer

Whenin use, my c80 emits a series of 3 loud beeps


You have triggered MOB (man over board) press and hold the MOB button in for 30 seconds.

Jul 17, 2009 | Raymarine C80 GPS Receiver

1 Answer

I need a manuel in french


Hi!

You can free download the manual for Raymarine C80 GPS Receiver from the following link---

Raymarine C80 GPS Receiver Manual

Please do accept this solution and revert for further assistance.

Thanks
Rylee

Jul 08, 2009 | Raymarine C80 GPS Receiver

1 Answer

Manual Needed


Hi,

Not sure how old your post is but I have both the Micrologic Mariner Loran Operator's Guide and also the Operator's Manual available, Both are in excellent condition.

If you still need them, you can email me at:

rich@TheFishermansDiary.com

Capt. Rich

Mar 13, 2009 | SI-TEX MARINE E-LORAN

1 Answer

Converting loran numbers to GPS. Loran TD coversion won't let me put in my loran numbers. My loran numbers have more digits than it will allow me to put in.


When you enter the Loran coordinates, they should only be 6 digits with one decial point ie: 12345.6

On the chart the coordinates may be shown with a prefix such as as 9960-W14123.4. The prefix (9960-W) is not entered on the conversion screen. It has to be set up in the position format set up page in your GPS prior to doing the conversion.

For example on my Garmin 76CS, I go into the setup menu and select position format.
I scroll down through the list of formats until I find "LORAN TD" and press "enter".
In this screen I enter the master chain number, which is 9960 for my region in New England.
I also have to enter the "slave" stations which are designated as V,W,X,Y, or Z. For example, in my region, the "W" slave station always starts with the number 14 (ie:14123.4) and the "Y" slave station always starts with 44 (ie: 44123.4).
When I am in the conversion screen, I don't have to enter 9960-W because the GPS is already formatted for that.

You should also note that a LORAN TD converted to Lat/Lon will not be as accurate because there is some mathmatical error in the conversion equation.

Jul 20, 2008 | Garmin GPS

Not finding what you are looking for?
Raymarine C80 GPS Receiver Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raymarine GPS Experts

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Steve
Steve

Level 3 Expert

694 Answers

The Knight
The Knight

Level 3 Expert

74459 Answers

Are you a Raymarine GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...