My sewing machine will not sew it only makes holes in the fabric from the needle

try changing the needle--make sure it's the right needle for the
fabric being sewed
rethread the machine top and bobbin
make sure the bobbin is inserted into the bobbin case
it's also possible that the machine could have a timing problem
and needs to be checked

some sewing machines are self oiling some are not, instruction manual should tell,, when a sewing machine breaks needles it very possible that the machine is out of time & only a sewing machine repair shop has the tools to time the machine

Machine breaks needles
1.make sure you are using the right needle for your type of sewing machine.
Most machines can use generic Schmetz needles. There are cases where the machine will only use ones specified in the owners manual.
2.the presser foot may not be installed properly
3.use the correct needle for the type of fabric you are working with. To fine of needle on heavy fabric or to course a needle on silk or jersey can damage fabric.
4.let the feed dogs guide the fabric & the feed dogs will work with the presser foot .
5.the needle is not all the way in -push all the way up against the stop

also make sure to use the right tension for what your sewing
also clean under the needle plate & bobbin area for lint or loose threads

if these suggestions don't work & stop the needle breaking then it may be neccessary to have the machine serviced

Use size 60 for very fine (chiffon), size 70 for light weights like voile and cotton, 80 or 90 for medium weights such as a broadcloth, size 100 for denim and size 110 for something very heavy like a thick curtain or upholstery weight fabric. If you aren't sure what size to use, try pushing a needle into the fabric you are going to sew with your fingers, if it goes in easily and the hole it leaves is not noticeable then it is okay, if it leaves a big hole, then go down a size. If you use a needle that is too small on a fabric, then it is going to go blunt quickly or break.

good info here http://sewing.about.com/od/sewingmachineindex/ig/Sewing-Machine-Needles/Needle-Sizes.--94.htm on needle sizes.

Hello,
Here are a few things to try.

* Raise your feed dogs if your machine has this feature.

* When you start to sew a seam, hold the upper and bobbin thread tails. Hold them back and out of the way as you sew your first couple of stitches. This will keep them from getting caught in your machine.

* Your fabric may require a different needle. Generally, heavier fabrics require larger needles and thinner fabrics, smaller needles. You may also need a larger needle if you're sewing through many layers of fabric. And make sure to use a ballpoint needle for knit fabrics and a sharp needle for woven (or a universal needle for either). And make sure your needle is appropriate for the type of thread you're using.

* Adjust the pressure of your pressure foot, it may be too light for your fabric.

* If your upper thread and bobbin threads are different types, try using the same thread for both. And use a good quality, brand name thread.

* Change your needle plate. Try switching to a needle plate with a smaller hole (a straight stitch needle plate).

Important Note: If you change your needle plate, check to make sure your needle aligns perfectly with this smaller hole before starting to sew. A misaligned needle could hit the plate and break, which could be dangerous. And make sure to change your needle plate back for zigzag and other wide stitches.

I hope this helps.

Hello,
Here are several solutions for you to try.

* Your broken needle may have been too thin for your fabric. Make sure your replacement needle
is appropriate for the weight and type of your fabric and thread. You may also need a thicker needle if you’re sewing through bulky layers of fabric. When you insert your new needle, make sure it’s positioned correctly (usually with the flat side away from the bobbin, but consult your manual), that it goes all the way into the holder, and that the screw is securely tightened.


If there doesn’t seem to be a problem with your needle, try the following:

* Check your pressure foot to make sure it’s attached securely.

* Change your pressure foot. Your pressure foot may be bent, causing your needle to hit it.

* Don’t sew over pins. A needle that hits a pin can break. Always remove the pins from your fabric before they reach your needle.

* Don’t pull your fabric as you sew. You could be bending your needle back, causing it to hit your needle plate instead of going into the hole. Just guide your fabric, letting it feed on its own.

* Check your needle plate to make sure it's securely in position.

* Change your needle plate. If you’ve been using a straight stitch needle plate (a plate with a small hole, often used for sewing fine, delicate fabrics), switch to a needle plate with a wider hole.

* Check the position of your needle. Sewing machines with zigzag capability allow you to adjust the position of your needle, right,left, or center. If your needle is not positioned correctly, it may be hitting your needle plate or pressure foot.


I hope this helps.

Hello,
Here are several solutions to try.

- Re-thread your machine. It may be threaded incorrectly (backwards).

- Raise your feed dogs if your machine has this feature.

- When you start to sew a seam, hold the upper and bobbin thread tails. Hold them back and out of the way as you sew your first couple of stitches. This will keep them from getting caught in your machine.

- Reinsert your needle and make sure it goes all the way into the holder and that it’s positioned correctly – usually with the flat side away from the bobbin, but consult your machine’s manual to be sure.

- Change your needle, it may be blunt, bent, or otherwise damaged.

- Your fabric may require a different needle. Generally, heavier fabrics require larger needles and thinner fabrics, smaller needles. You may also need a larger needle if you’re sewing through many layers of fabric. And make sure to use a ballpoint needle for knit fabrics and a sharp needle for woven (or a universal needle for either). Make sure your needle is appropriate for the type of thread you’re using.

- Adjust the pressure of your pressure foot. It may be too light for your fabric.

- Change your thread. If your upper thread and bobbin threads are different types, try using the same thread for both. And use a good quality, brand name thread.

- Adjust your thread tension, It may be too tight or too loose.

- Change your needle plate. Try switching to a needle plate with a smaller hole (a straight stitch needle plate).

Important Note: After changing your needle plate, check to make sure your needle aligns perfectly with the smaller hole before starting to sew. A misaligned needle could hit the plate and break, which could be dangerous. And make sure to change your needle plate back for zigzag and other wide stitches.

I hope these solutions help you.

Hello,
Here are a few things to try.

* Raise your feed dogs if your machine has this feature.

* When you start to sew a seam, hold the upper and bobbin thread tails. Hold them back and out of the way as you sew your first couple of stitches. This will keep them from getting caught in your machine.



* Your fabric may require a different needle. Generally, heavier fabrics require larger needles and thinner fabrics, smaller needles. You may also need a larger needle if you’re sewing through many layers of fabric. And make sure to use a ballpoint needle for knit fabrics and a sharp needle for woven (or a universal needle for either). And make sure your needle is appropriate for the type of thread you’re using.


* Adjust the pressure of your pressure foot, it may be too light for your fabric.


* If your upper thread and bobbin threads are different types, try using the same thread for both. And use a good quality, brand name thread.



* Change your needle plate. Try switching to a needle plate with a smaller hole (a straight stitch needle plate).


Important Note: If you change your needle plate, check to make sure your needle aligns perfectly with this smaller hole before starting to sew. A misaligned needle could hit the plate and break, which could be dangerous. And make sure to change your needle plate back for zigzag and other wide stitches.

Hope this helps.

Hello,
Here are some solutions to try.

* When you insert your new needle, make sure it’s positioned correctly (usually with the flat side away from the bobbin, but consult your manual), that it goes all the way into the holder, and that the screw is securely tightened.


If there doesn’t seem to be a problem with your needle, try the following:

* Check your pressure foot and make sure it’s attached securely.


* Change your pressure foot Your pressure foot may be bent, causing your needle to hit it.


* Don’t sew over pins a needle that hits a pin can break. Always remove the pins from your fabric before they reach your needle.


* Don’t pull your fabric as you sew. You could be bending your needle back, causing it to hit your needle plate instead of going into the hole. Just guide your fabric, letting it feed on its own.


* Check your needle plate and make sure it's securely in position.


* Change your needle plate. If you’ve been using a straight stitch needle plate (a plate with a small hole, often used for sewing fine, delicate fabrics), switch to a needle plate with a wider hole.


* Check the position of your needle. Sewing machines with zigzag capability allow you to adjust the position of your needle – right, left, or center. If your needle is not positioned correctly, it may be hitting your needle plate or pressure foot.

Hope this helps.

Hello,
Here are some things to try.

* Your broken needles may have been too thin for your fabric. Make sure your replacement needle is appropriate for the weight and type of your fabric and thread. You may also need a thicker needle if you’re sewing through bulky layers of fabric.

* When you insert your new needle, make sure it’s positioned correctly (usually with the flat side
away from the bobbin, but consult your manual), that it goes all the way into the holder, and
that the screw is securely tightened.


If this doesn’t seem to be the problem

* Check your pressure foot
Make sure it’s attached securely.

* Change your pressure foot
Your pressure foot may be bent, causing your needle to hit it.

* Don’t sew over pins
A needle that hits a pin can break. Always remove the pins from your fabric before they reach your needle.

* Don’t pull your fabric as you sew
You could be bending your needle back, causing it to hit your needle plate instead of going into the hole. Just guide your fabric, letting it feed on its own.

* Check your needle plate
Make sure it's securely in position.

* Change your needle plate
If you’ve been using a straight stitch needle plate (a plate with a small hole, often used for
sewing fine, delicate fabrics), switch to a needle plate with a wider hole.

* Check the position of your needle
Sewing machines with zigzag capability allow you to adjust the position of your needle – right, left, or center. If your needle is not positioned correctly, it may be hitting your needle plate or pressure foot.

I hope this helps.