Question about Amplifiers & Preamps

1 Answer

Want to get instructional manual

I need to get the technical pro RX-S111 1000watt integrated amplifier with EQ. manual where can i get it?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 54 Answers
Re: want to get instructional manual

You must feed the amp with stereo imput then adjust amp for pro logic and activate all speakers to get all speakers going.

Posted on Dec 01, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Hello , when i connect my equalizer bose 901 to line 2 at back of the amp there is no sound difference between do that or do nothing , and it work very well whith my old yamaha 50 w ! same result when i...

If it's connected properly AND directly between the source and the amp it WILL sound much better.

Get the manual at It lists several connection scenarios.

Jan 14, 2011 | Yamaha AS2000 Integrated amplifier...

1 Answer

I do not have a problem, however I need to purchase a manual for my suvx500 amplifier.

Go to the following address:
There you will find both the user's manual, and the service manual for the Technics SU-VX500 receiver.

Oct 24, 2009 | Technics SUV500 2-Channel Amplifier

1 Answer

Yamaha RX-797 iPod Integration

I have a question first... are the 901's amplified by a separate amp as they should be in a multi-channel (non-stereo) setup?

Better yet read the following then decide if you have iy set up right to begin with. If so, I'd just treat the Ipod or Mac as auxilliary inputs on the receiver. :

I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great!

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out (or one of your analog Tape Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.

Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Write off the Tape Out as an input if you use it to extract the Front L&R channels. DO NOT monitor it or you'll chop the 901's out of the signal path AND kill any digital source audio in the receiver.

Jul 02, 2009 | Yamaha MX-D1 2-Channel Amplifier

2 Answers

Yamaha rx-797 w/Yamaha ge-60 eq utilizing prein/main out ..and ad

It sounds like you want to use the external amp rather than the internal one. If that is the case, just connect the output of the EQ to the input of the external amp. All you are doing is inserting the EQ between the amp stages now. Using the mx-1 rather than the internal amp is no different.


Feb 25, 2009 | Yamaha MX-D1 2-Channel Amplifier

1 Answer

Bose 901 equalizer

Hi Mark, had a look for a manual on your Yamaha, but not got to one as yet. Does it have any RCA connections on the back marked as preout prein? best place to put the 901 EQ is in line with L and R front channels at this preout prein point.

Some amps DO NOT HAVE IT. If our does not, then you could connect it in the tape loop, tape out(rec) to input on the EQ. and the output of the EQ connected to tape in(play), but connected like this, the EQ would affect the tone across all channels(unless you are just running a stereo rig, then this way works great!!) Try this and you may just have solved you problem anyway.


Mar 28, 2008 | Amplifiers & Preamps

Not finding what you are looking for?
Amplifiers & Preamps Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amplifiers & Preamps Experts


Level 3 Expert

4502 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

66352 Answers

Are you an Amplifier and Preamp Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides