Question about Samsung CLP-510N Laser Printer

2 Answers

Engine Fuser. Low Heat Error. How do I fix this?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 40 Answers

Take apart fuser&clean heat-control sensor by 90 alcohol. Because of ink sticked

Posted on Jul 30, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Samsung Master
  • 1,447 Answers

Please you change your printer heat roller or clean thermostator some of wast toner over thermostater so this massage are show

Posted on Jul 30, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 624 Answers

SOURCE: Engine Fuser Low Heat Error

Basically the error message is telling you the printer cannot keep the fuser temperature at the proper temperature (too low). It could be a lot of things but typically it is due to a fuser assembly gone bad.

Posted on Feb 21, 2007

samkong
  • 106 Answers

SOURCE: ML 3561ND engine fuser. low heat error??????

If you have annother tonner cartridge, (the old one will do)fix it and see if it works. If not there might be a component faillure related to the Fuser Unit. Also check for any Jam in the Pinions(Sometimes Samsung Laser Displays wrong MSG.)

Posted on May 06, 2007

  • 883 Answers

SOURCE: Engine Fuser Low Heat Error

there is a 2 wire device (thermistor) that rests against the fuser roller to measure the temperauture. if the fuser is getting quite hot, suspect the thermistor to be either dirty (remove and clean it with alcohol) or defective. if fuser not getting hot, then suspect burned out fuser heater (look inside fuser roller for a long light bulb).

Posted on Aug 28, 2007

SOURCE: Engine Fuser Low Heat Error

I have the same probolem with the Samsung color laser printer clp-510. I get the "engine fuser low hear error"
What can I do?

How do I get the diagnostic software to try that too?

Posted on Dec 19, 2007

  • 3 Answers

SOURCE: low heater error

I bought another second hand one for € 40,00 and replaced the unit. It's just 5 screws and on we go again.

I have a CLP 500 and bought a CLP510N. The units are the same. unfortunately not all parts on the machine are the same, but for now mine works again.

Posted on May 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine fuser low heat error what is it and how do I fix it


Either the lamp or the sensor is bad on the fuser, check www.precisionroller.com for a new fuser.

Oct 29, 2009 | Samsung CLP-500 Laser Printer

2 Answers

Engine Fuser Low Heat Error


Hello,

You need to replace the fuser in the printer, the part number is JC96-03406A You can do a google search for the best price.

I hope this helps, If so please rate my solution.

Buddy
Corporate Computer
www.ccl-la.com

Jul 30, 2009 | Samsung ML-3561N Laser Printer

1 Answer

Low heat fuser


The fuser is not heating up, a lamp could be out, but usually the rollers are worn and it's best to replace the fuser completely.

Jun 29, 2009 | Samsung CLP-510 Laser Printer

1 Answer

Error Message-


there is a thermostat circuit that regulates the temperature of the fuser. A sensor reads its tempurator and something is out of wack -either the sensor or the sensor tempurature circuit .

Dec 21, 2008 | Samsung CLP-500 Laser Printer

3 Answers

Engine Fuser Low Heat Error


What this means is that the fuser is not reaching operating temperature. The most common reason for this failure is the xenon lamp inside the heat roller of the fuser has burned out. You can verify this by checking for continuity between the two contacts that connect to the lamp with an Ohm meter or digital multi meter.

If the continuity is good, the second most common reason for failure would be the LVPS, or low voltage power supply.

And last, although by far the least common reason for this error is the main logic board.

Have you checked to see if the unit is under warranty? If so, this would be a covered repair.

The part number for the fuser is listed below. Depending on your location and electrical system ( 110 or 220 )

ELA UNIT-FUSER 230V part number :JC96-03239A for use with 230V
ELA UNIT-FUSER 110V part number :JC96-03239B for use with 110V

Other then samsung, you can try a google search, and also an ebay search for the part number and find the best price for the item.

Good luck,

Cory

Nov 04, 2008 | Samsung CLP-510 Laser Printer

1 Answer

"Low Heat Error"


Thats probably the best way to solve the solution. Sometimes if there is a thermistor that is causing the problem that can be serviceable in the fuser unit, that can be replaced instead of purchasing a whole new fuser assembly. It's less expensive replacing the thermistor.

Jul 16, 2008 | Samsung CLP-600N Laser Printer

1 Answer

How do I fix an Engine Fuser Low heat error on printer:


UNPLUG AND REMOVE 5 SCREWS ON THE FUSER HOUSEING . CK WITH METER TO THERMOFUSE

Nov 05, 2007 | Samsung CLP-550N Laser Printer

3 Answers

Engine Fuser Low Heat Error


THERMO FUSE OR THERMISTOR DIRTY OR BAD

Nov 05, 2007 | Samsung CLP-550N Laser Printer

2 Answers

Engine Fuser Low Heat Error


there is a 2 wire device (thermistor) that rests against the fuser roller to measure the temperauture. if the fuser is getting quite hot, suspect the thermistor to be either dirty (remove and clean it with alcohol) or defective. if fuser not getting hot, then suspect burned out fuser heater (look inside fuser roller for a long light bulb).

Aug 28, 2007 | Samsung CLP-510 Laser Printer

3 Answers

Engine Fuser Low Heat Error


Basically the error message is telling you the printer cannot keep the fuser temperature at the proper temperature (too low). It could be a lot of things but typically it is due to a fuser assembly gone bad.

Feb 20, 2007 | Samsung ML-2551N Laser Printer

Not finding what you are looking for?
Samsung CLP-510N Laser Printer Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

HEMANT GROVER

Level 2 Expert

167 Answers

Victorman
Victorman

Level 3 Expert

822 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...