Question about Relic Watches

1 Answer

How do you get crown out to set time on Relic hybrid smart watch. I can;t get it out. Directions on website say pull out 3 clicks but it will not pull out

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 39 Answers

You may find it is a screw down crown. try screwing the crown anti clock wise until it is undone then proceed with the two clicks

Posted on Jan 03, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to an Expert (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: seiko watch stuck crown

The crown maybe a screwdown type. Try unscrewing (like jar lid)them pulling out the crown.

Posted on May 04, 2007

  • 1 Answer

SOURCE: Watch Band Adjustment

I just got this watch for a gift and was able to remove links myself after doing some research. It really isn't difficult if you are patient, have a little mechanical experience, and have some very basic "tools" available.

Tools:

  • 1 push pin like you use on bulletin boards with a plastic head
  • 1 small hammer like a tack hammer
  • 1 pair of small pliers. Needle nose pliers would be best but I used diagonal wire cutters (be careful not to cut the link pin)
  • 1 small block of wood

Try to pick a well lit table in a room where you will not be interrupted.

Procedure:
1. Lay the watch and band sideways on the block of wood so that a pin for the link you would like to remove is just hanging over the edge of the block and pointing down. You need the block to brace the band while you hammer lightly on the pin. Someone to hold the watch in that position would be helpful, but it can be done alone. Only try to remove pins that have an arrow on the back of the band pointing at them. It does not matter with this watch band which way you go with the pin.
2. Carefully line up the push pin point with the top of the pin.
3. Slowly, lightly and carefully hammer the plastic side of the push pin so that the pin in the link just emerges from the band on the bottom side enough so that you can grab it with the small pliers.
4. Slowly and carefully pull the pin straight out with the pliers. You can pick up the watch from the block of wood to get a better grip. Be careful not to bend the pin since you will need to replace at least one of the pins you remove.
5. Repeat steps 1 - 4 until the band is the correct length. I needed to take out 3 so I removed 2 from one side and 1 from the other side of the clasp.
6. To fasten the watch back together again, gently insert the pin back in the hole it came from it. You will probably need to use the tack hammer to make the top of the pin flush with the band.

Posted on Jan 09, 2008

escapement
  • 2334 Answers

SOURCE: taking back off relic watch

If this is screwback, then there should be grooves for inserting case opener claws. For this yoy need case opener with interchangeable claws. You can buy it on ebay for approx. £7.00.
If the casebask is snap-on, then there shouldn't be any grooves, just small opening (lip) between the caseback and case. This is exact point where the watchmakers knife blade must be inserted and pryed up.
Do not forget to rate, please.

Posted on Jan 26, 2009

  • 1 Answer

SOURCE: setting time Wenger Swiss military brigade hinged crown protector

The crown protector is hinged on the lower end only. The upper end can be pulled away to expose the crown for time setting.

Posted on Jul 12, 2009

mcdevito75
  • 1970 Answers

SOURCE: how do you pull the crown out on and invicta watch

mcdevito75 here, Your invicta may have a screw down crown that adds water proof protection to your watch, try to un-=screw the crown when un- screwed then pull up to set time.

Posted on Jun 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the day, date etc on a GENEVA 7391 watch


read the instruction manual, Geneva Watches with Two or Three Hands
  1. Pull the crown out until you feel a click.
  2. Turn the crown counterclockwise until you have the correct time.
  3. Push the crown back in to set the time.
Geneva Watches with Two or Three Hands and a Date Window
  1. Pull the crown out until you feel two clicks. This second click position allows you to set the time.
  2. Turn the crown counter clockwise until you have the correct time. Push the crown all the way in to set the time.
  3. Pull the crown out until you feel one click. This first click position allows you to set the date.
  4. Turn the crown counterclockwise until you have the correct date. Push the crown back in to set the date.
Multi-Function Geneva Watches
  1. Pull the crown out until you feel two clicks. This second click position allows you to set the day.
  2. Rotate the crown counter clockwise until you have the correct day. Push the crown in to set the day.
  3. Pull the crown out until you feel a second click to set the time or the 24-hour hand.
  4. Turn the crown clockwise until you have the correct time, then push the crown in to set it.
  5. Pull the crown out just one click to set the date. Turn the crown clockwise until you have the correct date, then push the crown in to set it.
Geneva Chronograph Watches
  1. Pull the crown out two clicks. This second click position allows you to set the time.
  2. Turn the crown clockwise until you have the correct time, then push the crown in to set it.
  3. Pull the crown out just one click to set the date. Turn the crown clockwise until you have the correct date, then push the crown in to set it.
  4. Stop and start the chronograph by pressing the PA button, located above the crown.
  5. Reset the chronograph by pressing the PB button just below the crown. The PB button returns the chronograph second and minute hands to their original positions of zero.
Automatic Geneva Watches
  1. Wind the mainspring by turning the crown 15 to 20 times clockwise.
  2. Pull the crown out until it clicks.
  3. Turn the crown counterclockwise until you have the correct time, then push the crown in to set the time.
Tips & Warnings
  • Do not set the date or time between 8 p.m. and 3 a.m. to avoid damage to your Geneva watch. The gears sit too close together during these times.
  • If your Geneva watch becomes wet, wipe it dry as soon as possible. Keep your watch away from saunas and hot tubs, as the extreme heat diminishes the watch's water resistance.




Read more : http://www.ehow.com/how_6134550_set-date-time-geneva-watch.html

Jul 13, 2015 | Geneva Watches

1 Answer

How to set the time and day and date on a relic zr15701


Pull the crown out once to set the date. Pull it out a second time to change the time. Of course move the crown up or down and see if it will change.

Dec 24, 2013 | Relic Degrade Pocket Watch

1 Answer

How do you set the time on a Relic ZR85049 pocket watch?


the crown in the top of 12 o'clock must be pulled. and turn it to adjust the time.

Jul 23, 2011 | Relic ZR85049 Pocket Watch for Men

1 Answer

I've lost the owner's instructions and need directions for setting the alarm.


  • Unscrew the crown (the main knob on the center right side of the watch casing), wait until the second hand is at the 12 o'clock position, and pull the crown knob up so that it clicks once.
  • 2 Press the button below the crown knob repeatedly until the hands of the alarm dial point to the time within the next 12 hours that you want the alarm to ring. Pressing the button once will move the alarm one minute forward. Pressing and holding the button will move the alarm forward quickly.
  • 3 Pull the crown knob one click further out and turn to adjust the main hands to the correct time, to take into account the time you took to set the alarm.
  • 4 Push the crown knob two clicks back into its normal position, and screw it into place until it locks.
  • Aug 20, 2010 | Pulsar PXH225 Watch

    1 Answer

    I purchased a Marco Max watch with day, date and moon phase. How do I set each of the dials to match the correct day of week, month and hour?


    The crown has three positions. The A position is when it’s pushed all the way in. You can’t set anything in this position. The C position is when it’s pulled all the way out. The B position is the click between all the way in and all the way out. My biggest problem is that I read the directions to mean that there were FOUR positions. I didn’t realize A was all the way in. I thought there was three pulled out positions.
    To set the day of the week (Sun, Mon, etc.): Pull the crown all the way out (position C) and turn the time to just after midnight. The setting will click to the next day. To advance it an additional day, you don’t have to turn the hands another twenty four hours. You can turn the hands backward to before midnight (you will see the day of the week setting click a little, but not go backwards), then turn the hands past midnight again.
    I recommend setting the day of the week setting to YESTERDAY. You’ll see why later.
    To set the date: 3341598183_60e77d12e5.jpgPull the crown one click out (position B) and turn the crown away from you (clockwise). This will advance the day indicator (it looks like a second hand). To set the month, you have to keep turning until you get past an entire year. There is no separate way to set the month. To make the correct month show, you must keep turning the crown past every day of the year until you get to the correct day.
    I recommend setting the date to YESTERDAY. I’ll explain why later.
    To set the moon phase: Pull the crown one click out (position B) and turn the crown toward you (counter clockwise). To find out what phase the moon is currently in, here are a couple of websites:
    Once again, set it to the moon phase for YESTERDAY.
    To set the time: Pull the crown all the way out (position C) and turn the crown either away or towards you to set the time. Keep turning the time away from you (clockwise) until you get past midnight. Once you get past midnight, ALL the settings should change (day of the week, date and moon phase). Now you KNOW you’re on today’s date at just after midnight. Set the correct time and your Luar watch is ready to go!
    Review 3342440924_5fa48ca4fe.jpgMany of the Swatch enthusiasts were disappointed that the Luar is a battery powered watch instead of an automatic. With a price tag of approximately $450, it’s a little much to expect an automatic with a real moon phase. I’ve talked at length about what I desire in a watch here:
    My desires have changed a lot since that day nearly four years ago when I went looking for the perfect
    The crown has three positions. The A position is when it’s pushed all the way in. You can’t set anything in this position. The C position is when it’s pulled all the way out. The B position is the click between all the way in and all the way out. My biggest problem is that I read the directions to mean that there were FOUR positions. I didn’t realize A was all the way in. I thought there was three pulled out positions.
    To set the day of the week (Sun, Mon, etc.): Pull the crown all the way out (position C) and turn the time to just after midnight. The setting will click to the next day. To advance it an additional day, you don’t have to turn the hands another twenty four hours. You can turn the hands backward to before midnight (you will see the day of the week setting click a little, but not go backwards), then turn the hands past midnight again.
    I recommend setting the day of the week setting to YESTERDAY. You’ll see why later.
    To set the date: Pull the crown one click out (position B) and turn the crown away from you (clockwise). This will advance the day indicator (it looks like a second hand). To set the month, you have to keep turning until you get past an entire year. There is no separate way to set the month. To make the correct month show, you must keep turning the crown past every day of the year until you get to the correct day.
    I recommend setting the date to YESTERDAY. I’ll explain why later.
    To set the moon phase: Pull the crown one click out (position B) and turn the crown toward you (counter clockwise). To find out what phase the moon is currently in, here are a couple of websites:

    Once again, set it to the moon phase for YESTERDAY.
    To set the time: Pull the crown all the way out (position C) and turn the crown either away or towards you to set the time. Keep turning the time away from you (clockwise) until you get past midnight. Once you get past midnight, ALL the settings should change (day of the week, date and moon phase). Now you KNOW you’re on today’s date at just after midnight. Set the correct time and your watch is ready to go!

    Aug 11, 2010 | Watches

    3 Answers

    How do I set the time and date on my Toy Watch?


    The Toy Watch website has instructions on setting the time. Not sure about the date:

    Setting Your TOYWATCH
    1. Unscrew crown by turning it toward you.
    2. Pull the crown out until you hear a click.
    3. Turn the crown to set the time as desired.
    4. Push in the crown and screw away from you until it is tight.*

    * If crown is loose warranty covering water damage may be voided. crown_locked.jpg

    http://toywatchusa.com/content/Setting.htm

    Jul 16, 2009 | Watches

    1 Answer

    Setting the time and date


    There isn;t any downloadable manuals for Rolex watches, but operation of Rolex Day-Date is very simple:
    1) when you unscrew the crown, it is in winding position,
    2) when you pull out the crown to the first click, it is in day and date setting position (depending wich way you turn the crown).
    NOTE: to adjust the day or date, previously you have to advance hands forward, passing 12 o'clock (midnight) mark and stop advancing at 4.00 a.m. using the crown in position as described in chapter 3. When done - push the crown fully in, then pull out to the first click and only then adjust the day or date.
    3) when you pull the crown further out to the second click, it is in time setting position.
    To find the daytime or night time on the watch: pull out crown to the second click and advance watch hands forward till you pass the 12 mark on dial. If the date changes as you pass it - it is the night time (midnight). If the date do not change as you pass it - it is the daytime (noon).
    After all settings being done, allways screw the crown back down as it protects the watch from water and moisture.
    Never use watch in sauna- it's not designed for that.
    Do not forget to rate, please.

    Jul 09, 2009 | Rolex Explorer II 16570 Wrist Watch

    1 Answer

    Winding and setting the time on a rolex watch


    There isn;t any downloadable manuals for Rolex watches, but operation of Rolex Day-Date is very simple:
    1) when you unscrew the crown, it is in winding position,
    2) when you pull out the crown to the first click, it is in day and date setting position (depending wich way you turn the crown).
    NOTE: to adjust the day or date, previously you have to advance hands forward, passing 12 o'clock (midnight) mark and stop advancing at 4.00 a.m. using the crown in position as described in chapter 3. When done - push the crown fully in, then pull out to the first click and only then adjust the day or date.
    3) when you pull the crown further out to the second click, it is in time setting position.
    To find the daytime or night time on the watch: pull out crown to the second click and advance watch hands forward till you pass the 12 mark on dial. If the date changes as you pass it - it is the night time (midnight). If the date do not change as you pass it - it is the daytime (noon).
    After all settings being done, allways screw the crown back down as it protects the watch from water and moisture.
    Never use watch in sauna- it's not designed for that.
    Do not forget to rate, please.

    Apr 04, 2009 | Rolex Watches

    1 Answer

    How do i wind and set my Rolex Oyster Perpetual watch


    There isn;t any downloadable manuals for Rolex watches, but operation of Rolex Day-Date is very simple:
    1) when you unscrew the crown, it is in winding position,
    2) when you pull out the crown to the first click, it is in day and date setting position (depending wich way you turn the crown).
    NOTE: to adjust the day or date, previously you have to advance hands forward, passing 12 o'clock (midnight) mark and stop advancing at 4.00 a.m. using the crown in position as described in chapter 3. When done - push the crown fully in, then pull out to the first click and only then adjust the day or date.
    3) when you pull the crown further out to the second click, it is in time setting position.
    To find the daytime or night time on the watch: pull out crown to the second click and advance watch hands forward till you pass the 12 mark on dial. If the date changes as you pass it - it is the night time (midnight). If the date do not change as you pass it - it is the daytime (noon).
    After all settings being done, always screw the crown back down as it protects the watch from water and moisture.
    Never use watch in sauna- it's not designed for that.
    Do not forget to rate, please.

    Apr 04, 2009 | Watches

    2 Answers

    How to set the time on relic watches


    I had to go to the Sears counter to fix mine. The sales person had to use TWEEZERS to pull the serrated knob up. He had to really work at it. Once it is pulled up you can twist the knob to set the time and then push the knob back down. What a stupid design.

    Dec 27, 2008 | Relic Degrade Pocket Watch

    Not finding what you are looking for?
    Watches Logo

    Related Topics:

    26 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Relic Watches Experts

    Les Dickinson
    Les Dickinson

    Level 3 Expert

    18411 Answers

    Ansel Alberto
    Ansel Alberto

    Level 2 Expert

    248 Answers

    deton8 von Splosion

    Level 3 Expert

    2942 Answers

    Are you a Relic Watch Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...