Question about Toshiba CZ36V51 36" TV
Occasionally when turning on my TV the red power light will blink and there will be sound but no picture. Then it will stop blinking and the picture will be perfect. It happens more often when you turn the tv on more then once a day or if I used the remote to shut it off.
No picture - screen is empty. Sound is ok
Check IC101 (BA7630F), if video signal comes to input (pin 1) but not present at output (pin 14) then replace this IC
No picture and sound, only a high pitch sound at switch on
Remove horizontal transistor and measure the resistance across any two pins. This value should be no less than 200ohms
Picture fades away few seconds after start-up till no picture. Sometimes no picture at all. Sometimes picture OK for longer. Sound unaffected.
Faulty joints on CRT pcb. Cracked solder joints at tube socket connections on CRT circuit board. Caused variable supply to CRT heaters. Resolder all socket pins to pcb.
Posted on Nov 24, 2007
Tips for a great answer:
May 04, 2013 | Standard (CRT) Televisions
Standby/Power light of the TV blinks when there is any internal malfunction in
the TV. The self-diagnostic function of the TV will cause the STANDBY light to
blink or flash when the television detects an issue. The number of times the
STANDBY light flashes corresponds to a specific issue.
examples are given below; some of the issues may be resolved without the need
1 blink / 2 blinks / 5 blinks: - This indicates that there may be a power-related problem with your set.
3 blinks: - This indicates that there may be a power-related problem with your set. The set will need to be serviced to allow a technician to determine the specific issue that needs to be repaired. If the power light flashes three times in sequence in a Lamp TV, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue.
4 blinks: - This indicates that there may be a back light or lamp power problem.
6 blinks: - This indicates that there is some kind of audio problem with your set.
7 blinks: - This indicates that there is a temperature problem with your set. Please check to make sure that the air vents on the sides and back of the set are not blocked or clogged and there is adequate ventilation around the television. We recommend that you check and clean the vents periodically to make sure the set receives adequate air flow. If the problem continues, the set will need to be serviced.
8 blinks: - This indicates that there may be a video-related problem with your set. If the flash sequence is not listed above or the light continues to flash, follow the steps below to perform a power reset:
Try the following steps to check if the issue can be resolved.
Turn off the television.
Unplug the television power cord from the electrical outlet.
Let the television remain without power for 60 seconds.
Plug the power cord back into the electrical outlet.
the television is plugged into a power strip or surge protector, remove it from
the power strip or surge protector and plug it directly into the wall outlet.
If the issue is resolved, the problem is with the power strip or surge
protector and not the television.
the issue continues to occur, service may be required.
for using Fixya.
Feb 04, 2011 | Sony FD Trinitron WEGA KV-32FS100 32" TV
Oct 11, 2010 | Sony FD Trinitron WEGA KV-20FS120 20" TV
Feb 14, 2010 | Sony FD Trinitron WEGA KV-36HS510 36" TV
Sep 27, 2009 | JVC AV-36D302 36" TV
Sep 13, 2009 | Panasonic CT-36HL43 36" TV
Jun 26, 2009 | Sony KV-35S42 35" TV
May 18, 2009 | Sony KV-36FV26 TV
Sep 17, 2008 | Panasonic CT-36HL43 36" TV
886 people viewed this question
Usually answered in minutes!