Question about Crosley Dryers

1 Answer

No water in washing/rinse cycle of dishwasher

Water in line but no water in washing/rinse cycle of dishwasher. System works when you pour water in before washing/rinsing cycle starts of crosley dishwasher

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 704 Answers

It sounds as if the warter inlet valve (solinoid) isn't working and might have to be replaced. If everything else opeates fine, (unit pumps and sprays water that you added to it, pumps out and drains OK, then it is very likely the inlet valve has failed.

You can check for a blockage in the water inlet line, but unless you have a lot of sediment in your water or use a private well for your water supply, that would be a remote possibility, but worth taking a look at before buying replacement parts, etc.

You can remove the water supply hose/line and check for proper water flow and see if there is anything blocking the water from getting into the dishwasher. Many uints have a filter screen installed in them, so check that to see if it is blocked. Otherwise, look at the inlet valve and see if it is working correctly and go from there in replacing it.

One last thing, make sure the water supply line is actually providing water to the dishwasher, sometimes the water valves some installers use do get blocked, depending on how it was installed.

Posted on Jul 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hobart SR24H dishwasher after rinse cycle the same time pampas water in and out of the dishwasher, two pipes are opened and working


Hello.
As per my personal opinion this is normal because for the final rinse you have a small booster or boiler..
When you turn on the machine..it starts fill and also the booster for the final rinse.
You start the machine..wash cycle...rinse cycle..
Now..new water(from rinse booster) is coming on the tank in order to rinse the dishes..on the same time the machine drains the excces water from the rinse(over flowing) and fills up the booster with new water.
Should be like this

Good luck

Jun 29, 2013 | Dishwashers

1 Answer

Maytag DWU8330AAX: glasses, plates, utensils,


Hi,

The rinse cycle is the same as the wash except the wash uses detergent and the rinse uses rinse aid.

The rinse cycle will dispense rinse aid if you have filled the dispenser. Check this first, that would be the most likely cause. Also in the spring as the water table table in most cities begins to rise the water quality goes down, extra calcium in the water can cause this problem.

Here is a link to help understand that. Let me know if you have questions.

http://www.fixya.com/support/r4666624-hard_water_calcium_white_powder_build_up

May 02, 2010 | Dishwashers

1 Answer

Water pump evacuates water but does not pump in the wash or rinse


You assume correct. The control board switches the direction, but if there's a mechanical problem like a bad start capacitor, then it won't run

Jul 29, 2017 | Kelvinator MDB121RF Dishwasher

1 Answer

Soap in JetDry dispenser.


Unfortunately there is no easy way to completely get the detergent out of the rinse aid reservoir in one quick method, short of taking the inside panel off the door.

However, I would try a simple way to flush it out. With the door open almost al the way open, pour warm/hot water into the rinse aid fill hole and keep pouring until you start to get clear water coming out. The water will be flowing back out the fill hole you're pouring the water into and should just flow down the door panel into the dishwasher tub. Try to keep the door about 10-15 degrees up from all the way open to let the water get in the rinse aid reservoir.

Just pour the water in slowing so you don't agitate the mixture and you should be able to get it running clear in 5-10 minutes. It could take a gallon or so of warm/hot water to accomplish this, but it will flush it.

When you'r done, just put the dishwasher into a rinse cycle to pump out the water and soap, etc. You may have to run a full cycle afterwards to get rid of any excess detergent in the tub.

Hope this helps and best regards!

Aug 03, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Dishwasher doesnt drain on wash cycle,ok on rinse cycle


Change the circuit board, timer/progrsmer.
Take it out and clean contacts,
Look for burnt circuit line and solder a fine bead carefully on the circuit board, difficult. Use the pot and pan program.
Vitally

May 03, 2009 | Maytag MDB7100AWB Dishwasher

1 Answer

Frigidaire fdb1050rem2 dishwasher will not drain during was cycle


Checked water temperature at water heater. It was at 110 degrees. Turned water heater up to 125 degrees. Dishwasher works perfectly now.

Mar 30, 2009 | Frigidaire 24 in. FDB1050REC Stainless...

1 Answer

No water going in to dishwasher when rinsing


the pump shouldn't turn on when the rinse cycle is on - it uses only fresh water straight from the water line - after the wash cycle is over - wait 5 seconds, then open the doors and see if there is any rinse coming out of the rinse arms.
If only a little is coming out - check the rinse arm spray jets to see if there is debris caught in them -
if no water is coming out - it could be a faulty rinse solenoid

Aug 05, 2008 | Hobart AM14-253 Free-standing Dishwasher

2 Answers

The correct way to start the wash cycle


we have just purchased a Fagor dishwasher also - the instruction manual is worthless.

in regards to the 2 thin tubes, we just inserted them in the gallon jugs that the soap/rinse agents comes in and it works fine. just make sure the clear tube without the label goes in the rinse agent and the labeled tube goes in the soap jug. we did drill a hole in the top cap of the jugs and pushed the line thru and that helped keeping the tubes in the jugs and minimized the mess if the jugs fell over.

in regards to the temperature problem, we found that running it thru a couple of cycles before you start the actual dishes helped get the water temperature up faster. it seems to like to start with normal tap hot water first, so the 1st couple of cycles get the cold water out of the line.


Dec 29, 2007 | Fagor 24 in. FI-48W Dishwasher

1 Answer

Dishwasher


Check to see if you have any switches on your dishwasher that could by pass a rinse cycle. Use a hotter temparture when washing, Check your water level,check your filters on your inlet hose top and bottom. When it gets to a rinse cycle you should hear it drain out and bring in fresh water. you could change to a liquid detergent. Dont over load your dishwasher. make sure you are using rinse aid and try adjusting it up one setting. Shiney glasses means your rinse add is working. NZL

Jan 04, 2007 | Kenmore 18 in. 14432 / 14439 Built-in...

Not finding what you are looking for?
Dryers Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crosley Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

charles

Level 2 Expert

97 Answers

Are you a Crosley Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...