Question about GE Profile Harmony DPGT750EC Electric Dryer

1 Answer

What does the codes mean.. when you hit the co mbination buttons?

Hi. Ive tried to read the diagnostics but.. what does the messages mean?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 262 Answers
Re: what does the codes mean.. when you hit the co...


Posted on Dec 11, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

The dryer is giving a code E68, and stop drying.

The error code means a key is stuck; enter the service diagnostic mode and perform the key test to determine which key is stuck. Once the key is determined, try to unstuck it; u may have to replace the electronic control board if the error code continues to appear after the button is unstuck.

Press and hold simultaneously the Select and Cancel buttons for six seconds to reset the control then immediately after the buzzer sounds, turn the cycle selector knob 5 clicks counterclockwise to position the cycle indicator light second (Touch Up) from the bottom.

Press and hold the Options and Cancel button simultaneously for two seconds to enter the service diagnostic mode. The buzzer will sound three times and all of the LEDs will flash indicating the service diagnostic mode has been entered successfully.

Rotate the cycle selector knob 4 clicks to the Heavy Duty cycle; the motor runs with the heater off. The buttons can now be tested. Press each button and all corresponding LEDs should flash; otherwise the button is stuck or a faulty. Unstuck the key and perform the key test again; replace the control board if the problem is not resolved.

Access to the control board requires the removal of the top panel and the console. Disconnect power to the dryer prior to servicing to avoid the risk of electric shock.

Remove the two screws attaching the top panel to the rear of the dryer then slide the panel rearward and lift it off the dryer.

Remove the four screws, two on each side, securing the console to the front panel then flip the console forward. Disconnect the wires from the control board and lift the console off.

Remove the five screws mounting the control board to the console and lift the control off. Remove the control board's rear cover by releasing the two locking tabs the flip the cover off the control board. Try to unstuck the faulty key and reassemble the dryer in reverse of the disassembly steps

Read more:

Apr 25, 2015 | Dryers

1 Answer

It keeps showing an error code C0. what does this mean.

Hi, I cannot find this error code for your dryer.
Does the dryer have other faults?
The Technical manual for the drier shows error codes, but does not include CO. The manual will help with resolving problems you may have as it has detailed instructions for troubleshooting and the solutions. See the diagnostic tests. You can also clear diagnostic codes, which may resolve this problem if there are no other problems with the drier.
You can download the manual from
Hope this helps you :)

Mar 04, 2015 | Amana NED7200TW Electric Dryer

1 Answer

Why is my Maytag Epicz model #MGDZ600TW2 not starting amd giving me an error code F01. What does it mean?

F01 is a control unit failure does this come up when you push the start button or did you go into diagnostic to get this code I have seen it come up as a false code check the start button does it spring back like all the other buttons if so replace control if not the button is broke

Jan 29, 2015 | Maytag Dryers

1 Answer

How do i reset code e63

your coils in the heating unit are touching the can you will need to clear them probably have to replace a broken porcelin insulator once you do this then you can reset the machine.
factory reset, press and hold the temperature and dry level buttons simultaneously for 6 seconds for models with temperature and dry level and dry time buttons press and hold the drylevel and dry time buttons simultaneously for 6 seconds.
diagnostic mode press the cancel button to enter standby mode and enable diagnostic entry.within 10 seconds after pressing cancel press and button but cancel to wake up the control. within 5 seconds of wake up turnthe selector knob to the far left cycle and press and hold the cancel and the center button under the display simultaneously for 3 seconds to enter the diagnostic mode. upon entering diagnostic mode all lights should flash on and off turn the selector knob clock wise on setting, you will need a book inside the dryer to read the codes pop off the top of the dryer it should be folded down in the front of the machine...

Jul 29, 2012 | Electrolux EIED55H Dryer

1 Answer

Need trouble shooting proceedure to enter self diagnostics for maytag neptune

From the service manual there is more to it but that was all I could put here.
Accessing Service/Diagnostic Mode:
Pressing down the damp dry and time (-) keys
for 5 seconds places the machine in the
diagnostic mode.
The following table lists the various tests
available while in the Service Mode, which
can be accessed by pressing the following
Press Keys Special Test/ Function
release Diagnostic Codes
temp(^ )
Sequences up the
help/diagnostic code list
dryer temp(v) Sequences down the
help/diagnostic code list
time (-) Displays Software Revision
very dry(< ) View current cycle
temperature (Co)
Start or pause cycle running
but remain in Diagnostic
Accessing Diagnostic Codes
After the machine is in the diagnostic mode,
a ‘d’ will display and let the technician know
they are in the diagnostic mode. Pressing the
wrinkle release key will access the diagnostic
codes.The diagnostic codes can be viewed by
using the temperature (^) & (v) keys.
The down arrow key will sequence down the
list one each time it is pushed with no wrap.
The first time the down arrow key is pushed
the display will sequence to the next code
logged. The last code being displayed being
the oldest code. The up arrow will sequence
up the list one code each time it is pushed
until it reaches the top code. If there are no
diagnostic codes available, ‘00‘ will be
displayed for the diagnostic code.
There will be no multiple occurrences of
either a diagnostic code or help code generated
in the same cycle reported on the list.
But if the same code occurs in repeated
cycles, it will be registered.
To clear the diagnostic code list press
wrinkle prevent and very dry (>) for 5
seconds while viewing the list.
System Check Mode
While in diagnostic mode, pressing the damp
and signal (+) keys for 2 seconds, will
put the dryer into the system check mode.
"SC" will display.
This mode will allow the various inputs and
outputs to be controlled and viewed by the
technician by pressing individual keys. If no
activity is seen for 5 minutes after a key is
depressed, the control will reset back to the
normal mode. If no further activity is seen
after an additional 5 minutes the washer will
turn off. The following table lists the various
functions based upon on keys being depressed.
Membrane Pad Check
While in system check mode, pressing the
damp dry and sensor dry keys for 5 seconds,
will start a membrane pad switch test.
The membrane check involves turning all the
embedded LED on the membrane pad on.
All the LED’s can be toggled off by pressing
the key associated with the LED. To exit the
test at any point, press the damp dry (>) &
sensor dry keys again for 5 seconds or press
the off key to exit diagnostic mode.
Key Pressed: Function Performed
sensor dry
Enable sensor dry circuit.
(sense dry LED) When short
circuit is detected across the
sensor bars the normal dry
LED will turn on.
start/ pause
Cycles the motor relay
on/off. When the motor is
running the start/pause LED
is on.
dry temp(^ )
If motor is running, cycles
the heater/gas valve on/off.
When the heater is regular
temp LED is on.
very dry(< ) View current cycle
temperature (Co)

Mar 26, 2010 | Maytag Neptune MDG5500AW Gas Dryer

1 Answer

Whirlpool gas dryer doesn't run. error code pf shows on lcd

pf usually means power failure. Try to clear the screen or hit the off button to clear pf and then see if it works.

Nov 16, 2008 | Whirlpool GGQ8831L Gas Dryer

2 Answers

Ge adora problem with panel code e01

I'm almost having the same issues but the code displayed is E62. Can you help

Aug 23, 2008 | GE DCVH515EF Electric Dryer

2 Answers

Dryer has power won't start cycle

Hi, check first the power outlet , if still does not turn and motor humming during starting time , test the capacitor with multi tester, disconnect two wire of capacitor if not reading replace capacitor .

Jan 20, 2008 | Kenmore Elite HE4 Electric Dryer

Not finding what you are looking for?
GE Profile Harmony DPGT750EC Electric Dryer Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dryers Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

John Tripp
John Tripp

Level 3 Expert

4625 Answers


Level 3 Expert

2963 Answers

Are you a GE Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides