Question about Hoover Washing Machines

Open Question

I have a Hoover HNF 7148-80 Nextra Optima where the pump is continually running. I need to reset the machine. How can I do this? Thanks.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Trifect7
  • 57 Answers

SOURCE: hoover nextra hnf 3671 -

If the washer doesn't operate or make any noise when set on any cycle, or if it stops suddenly when it should continue onto the next cycle, it may not be receiving electrical power or, if the motor stopped mid-cycle, the machine's overload protector may have tripped. In this case, take out some of the articles to reduce the load and let the protector reset itself, then restart. Otherwise:
1) Be sure it is plugged in and turned on. If necessary, check the receptacle it's plugged into for power, using a working lamp, appliance, or voltage tester. Be sure the washer lid is closed completely.
2) If the receptacle seems dead, check the circuit breaker or fuse that serves that circuit.
3) Unplug the washer and check the power cord. If necessary, replace the cord if you feel qualified.
4) Open the lid and check the lid switch and the tab on the lid that it pushes against. Press and release the switch: if it doesn't click when you do this, it's probably broken. If you're experienced at home repair, you can remove the switch, test it, and replace it if needed; otherwise, call an appliance repair service person.
5) If the washer still doesn't work, the controls may be faulty. Call a service person.

Posted on Mar 02, 2008

barkencoa
  • 3463 Answers

SOURCE: my hoover optima washing machine

Make sure it is not on rinse hold or crease care, release if it is, make sure pump is working, and that the cold inlet valve is working., all of these things could prevent it from completing rinse cycle.
Plz rate this solution.
Thanks.

Posted on Dec 18, 2008

  • 2 Answers

SOURCE: Error message EC03 appears on cotton cycle after 5 minutes into wash

I found the basic instructions that came with the washing machine and found that you need a screwdriver to undo a screw to remove the filter cover. I then gradually released the filter cover to empty the water out of the machine in small quantities into a shallow tray. I was then able to remove the filter and clear it of 2 x 20p pieces and a load of gunk. I then removed the 'washable' floormat from the drum as the rubber backing from the mat was crumbling and probably not helping the filter. Filter cleaned and cover screwed back in, mat in the bin, and everything working fine since.

I did try ringing the customer support number and after pressing loads of keys to select appropriate options; confirming my address, postcode, name, date of birth, email address, mothers maiden name, what the kids had for breakfast etc, I was allowed to ask how to get the filter cover off. Apparently this is a technical query and would involve arranging an engineer to call. I declined this very kind service option and opted for a screw driver, common sense and a positive attitude. Worked for me! No blood shed, a tiny bit of sweat whilst trying to get through on phone, and only tears of joy when I fixed it all by myself.

Posted on Jun 02, 2009

  • 574 Answers

SOURCE: hoover nextra washing machine , not draining

take pump off and take apart to clean

Posted on Aug 28, 2009

  • 3 Answers

SOURCE: How do you remove the filter for a Hoover washing

I included a link on Youtube to my Nextra where I show how I clean the filter (watch it from 08:55 onwords). Just remove the kick strip and unscrew (philips screwdriver needed) the little screw on the filter itself, then turn it anti-clockwise but while you're doing this make sure you insert the kick strip underneath to gather the residual water. Repeat this operation 3 o 4 times until the sump is totally empty, make sure you don't let the kick strip fill up too much otherwise you'll be spilling water all over the place, so just turn the filter clockwise everytime you want to stop the trickle of water. It's not too complicated and it won't be too messy if you follow these instructions carefully. Good luck ;-)

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nextra is shaking itself to bits and extremely


sounds like the bearing has gone possibly taken out the drum support to shaking could also be one of the wieghts has worked loose.

Mar 15, 2010 | Hoover Nextra HNF 3157 Front Load Washer

2 Answers

Hoover Nextra HNF2127 washing machine. Lights flashing at finish


Hi


Thanks for using FixYa. The start and pre-wash usually flash due to a clogged drain hose or the water pump. You’ll need to drain the water out of the base and also check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine). If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Feb 18, 2010 | Hoover Nextra HNF 2137 Front Load Washer

1 Answer

Machine not draining


Can you hear the pump running just before the spin cycle, if so then I suspect a blockage in the filter or pump hose, If not and machine is quiet then it could be a faulty water pump or PCB board and you would have to call a technician.

Apr 13, 2009 | Hoover Nextra HNF 2137 Front Load Washer

1 Answer

Programme problems hoover nextra megaload


I had this problem soon after I purchased mine. The engineer came out and readjusted the dial. Hope this helps.

Feb 26, 2009 | Hoover Nextra HNF 3157 Front Load Washer

1 Answer

My hoover optima washing machine model no. HNF 6127 keeps stopping when it gets to the rinse cycle


Make sure it is not on rinse hold or crease care, release if it is, make sure pump is working, and that the cold inlet valve is working., all of these things could prevent it from completing rinse cycle.
Plz rate this solution.
Thanks.

Dec 16, 2008 | Hoover Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

shaun taylor

Level 3 Expert

1525 Answers

Johnny Ramirez
Johnny Ramirez

Level 2 Expert

116 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...