Question about Lynx Health & Beauty

1 Answer

What does the code mean when light flashes 5 times was flashing 7 times and I replaced the speed control switch.

This is on a Lynx scooter

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 827 Answers

Posted on Aug 13, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: i have a Fujitsu ASTA24LCC

Check your filters. Manual says they need to be cleaned every two weeks under normal operation (and in my case more often during renovations). It seems it may not take much to limit air flow enough for the indoor unit to trip out. Hope this helps.

Posted on Aug 24, 2008

  • 1861 Answers

SOURCE: 1993 Camry Check Engine Light

Therre is no DTC code "5". The DTCs start at 12. If the knock sensor (there are actually 2) was bad, you would have an acceleration issue. The knock sensor changes the timing of the spark to eliminate detonation, or "pinging". Do you have a "Ping" condition/valve rattle on acceleration?
To reset the light, open the hood, remove the 15 amp EFI fuse for 5 minutes. Replace it, and start the car and drive it until it reaches operating temperature. If the light comes back on instantly, you have a bad sensor or a bad wire.

Posted on Nov 10, 2008

  • 1 Answer

SOURCE: Panasonic PT-50DL54J DLP TV Flashing Light

I had the same problems that most of you have been having, tv turning on and off, lights flashing in all different colors, having to unplug tv to reset and all of that good stuff. I noticed that most of the time this would happen once the tv would start to heat up, and I could hear the fan working a little harder. Well I am not an electrician but It was very simple to unscrew the lower bottom park of the tv, where the fan and most of the electronics sit, then I used an oxygen tank ( I work for a medical company ) to blow out all the dust in the tv, ( you can olso use the compressed air use for computer, but if grandma or grampa have some O2 laying around, it works really good, LOL. )and was very surpriced to see how dusty it was, then I removed the MAIN FAN ( you only need to remove three screws, however there's a box in fron of it, which you'll have to remove first in order to get to the fan ). this may sound a little complicated, but trust me it is not, once you have taken the fan off, clean it all the way around ( best to use a clean rag, the compressed air was not doing the job.
long story short, once I cleaned the fan and put it all back together. The TV still didn't work LOL, Just kidding, It has been working perfect for a little over a week.
If I can help in any other way, please e-mail me @ gsierra11@yahoo.com

hope this helps.

Posted on Feb 19, 2009

  • 11 Answers

SOURCE: Lexus RX330 - "Maintence Required Light" flashes 7 times?

reset: turn ignition on...push odometer button till it displays mileage on car...not trip milage but actual mileage. Turn car off. Open driver's door, press and hold odometer button....turn ignition to on....hold odometer button for 10 seconds....odometer display will show -----,----,---,--,-,0000000....maintenance lights are reset...lights will come on every 7500 miles to remind you to change oil and check fluids etec....

Posted on Jun 06, 2009

Therinnaiguy
  • 1420 Answers

SOURCE: 3 flashing light....Aire-Flo furnace AF80MPA100B5A

That control board is several hundred dollars. If I may make a suggestion, take a jumper and when the inducer fan starts, jump out the pressure switch. If it starts, it's not the board but a bad switch, hose or blocked exhaust vent.

Posted on Jan 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lynx 3 scooter wont go .power gage is full. But no movement.green kight flashes 5 x after i push the horn.


I expect the green light is telling you what the fault might be. If your instruction book doesn't provide the code you should contact the dealer or visit the manufacturer's website.

May 18, 2016 | Lynx Health & Beauty

1 Answer

Light is blinking a 7 fault code, what does this fault code mean.


According to the owner's manual for this scooter, flash code 7 indicates a speed control lever fault. This is the lever that you push to go forward and reverse. The lever is attached to a throttle potentiometer to control the speed of the scooter. The lever has to be in the middle or neutral position when the scooter is turned on, if not, you will get a 7 flash code. If the throttle potentiometer is damaged you will also get a flash code 7.
You can try to adjust the throttle pot or try manipulating the neutral position and turning the scooter on and off until the computer sees neutral. This is a potential work around and will cause the scooter to creep forward when running with hands off the throttle lever because there is no zero setting. I usually just replace the throttle potentiometer and this solves the problem. I hope this helps.

Oct 23, 2014 | Drive Medical Spitfire Travel 4-Wheel...

1 Answer

Rio 4 lightweight light flashes but doesn't drive


hi, please can you tell the number of flashes before a pause then it starts flashing again ?

Regards
Rob

www.gewizrepairs.co.uk

Mar 23, 2014 | Invacare Lynx 3-Wheel Lightweight Portable...

1 Answer

My Lynx L4 4-Wheel scooter green light flashing but it said it is charge it wont go forward


the green flashing light indicates an error with the scooter. Count the number of flashes 4 flashes pause 4 flashes pause etc and your manual should give you the meaning of the flashes Check to make sure that you are not in freewheel move the lever at the back of the scooter up and down a few times and make sure you leave it in drive mode turn on the power and see if the light stops flashing and the scooter will operate correctly Hope this helps

Oct 03, 2010 | Activeforever Lynx L4 Portable Mobility 4...

1 Answer

I have a golden companion scooter and it wont move it flashes a green light but i haave no info on where to obtain the trouble codes


The L.E.D. located on the tiller
dashboard will indicate with flash codes what problem is occurring.
L.E.D. Flashes 1 time and pauses, 1 time and pauses…. Batteries are low,
scooter will still operate.
L.E.D. Flashes 2 times and pauses, 2 times and pauses…. Batteries are very
low, scooter will not operate.
L.E.D. Flashes 3 times and pauses, 3 times and pauses….Over voltage to
controller.
L.E.D. Flashes 5 times and pauses, 5 times and pauses….Brake is in the
freewheel position or connection to brake is open.
L.E.D. Flashes 6 times and pauses, 6 times and pauses….Paddle or speed
potentiometer problem.
L.E.D. Flashes 7 times and pauses, 7 times and pauses….Paddle or speed
potentiometer problem.
L.E.D. Flashes 8 times and pauses, 8 times and pauses….Motor
disconnected or faulty.
L.E.D. Flashes 9 times and pauses, 9 times and pause….Controller fault.

I hope this helps they are pretty standard codes I got this from Golden Tech Web Site

Aug 17, 2010 | Golden Technologies Golden CompanioN II -...

1 Answer

Green light flashes 9 times will not go


Hi. Different brands of controllers give different fault codes.If this is a dynamic controller, 9 flashes is the code for a faulty controller. This does not always mean that the controller is actually at fault.
It could be a burn't out brake solenoid, that now has a different resistance through the solenoid coil.
You mention the middle speed green light is flashing, normally on dynamic controllers, it is the most left battery level LED that flashes. You might have a different controller.
Have a look under the panels and let us know what controller your machine has.
You could try the agents, and see if they can tell you what the problem is.
Good luck. Neil.

Jun 06, 2010 | Golden Technologies Companion II Travel...

1 Answer

Scooter moves approx 10 feet then stops led flashes 8 times then stops


Hi. 8 flashes is a fault code for a motor fault. It will be either worn brushes in the motor or faulty connectors to the motor. This fault code means that there is no circuit through the motor. Probably time to overhaul the motor. Most mobility scooters have plugs and sockets that are really to small to carry the amount of current that they do. Because of this, they sometimes fail.Good luck. Neil.

May 21, 2010 | Invacare Supply Group Invacare Lynx Large...

2 Answers

What is Invacare Supply Group? I have a Lynx-3 scooter. The scooter is not functioning. When I turn the key, there are 5 flashes. What problem is indicated by the 5 flashes? I need my scooter to get to...


Really i don't know the charge. Contact Fixya Team on support@fixya.com

Visit http://safemanuals.com/user-guide-instructions-owner-manual/LYNX/4TS630A-_E

Cheers

Mar 11, 2010 | Invacare Supply Group Invacare Scooter...

1 Answer

Hogh - low speed switch is incorrectly wired , but i dont know how it should be wired - Pride Hurricane scooter




Hi, I take it been taken then, do you get a error codes ?

see below


DIAGNOSTIC FLASH CODES
The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly and
easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed below
develops.
NOTE: Your scooter will not run unless the flash code condition is resolved and the scooter has been
turned off, then turned back on.
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
FLASH CODE CONDITION SOLUTION
! (1) Battery charge is low. Charge batteries as soon as possible.
! ! (2)
Batteries are too low to operate the
scooter.
Charge batteries.
! ! ! (3)
The scooter’s battery voltage is too
high to operate the scooter, or the
charger is still connected to charger
port.
Unplug charger and/or turn key off, then
back on again.
! ! ! ! (4) Current limit time out.
Turn the scooter off for a few minutes,
then turn your scooter back on.
! ! ! ! ! (5)
The manual freewheel lever is in the
(forward) freewheel position.
Remove the key from the key switch,
then push the manual freewheel lever to
the (rear) drive position, and restart your
scooter.
! ! ! ! ! ! (6)
Throttle control lever not at center
position at start up.
Return the throttle control lever to center
position, turn scooter off, then back on.
! ! ! ! ! ! ! (7) Speed pot error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! (8) Motor volts error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! ! (9) Other internal errors.
Contact your authorised Pride Dealer for


Regards
GeWiz.

Oct 20, 2009 | Pride Hurricane 4 Wheel Personal Mobility...

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lynx Health & Beauty Experts

Vernon Taylor

Level 3 Expert

2929 Answers

Robin Hill
Robin Hill

Level 3 Expert

1263 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14584 Answers

Are you a Lynx Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...