Question about One For All URC-3021 Remote Control

1 Answer

The coude I need to open with a coude it is not working

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 259 Answers
Re: the coude

If your device does not respond to the remote control after trying all codes
listed for your brand, or if your brand is not listed at all, try searching for
your code.
NOTE: Before performing a code search for a DVD player or a VCR, turn on the device and
insert the required media.
For example, to search for a code for your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red light) blinks twice,
then release SET.
3. Enter 9 - 9 - 1.The LED will blink twice.
4. Aim the remote control at the TV and slowly alternate
between pressing POWER and TV. Stop when the TV turns off
(after pressing POWER). If the device does not have a Power
key, you can substitute another function, such as digits 0 ~ 9 ,
CH, or PLAY).
NOTE: In the search mode, the remote control will send IR codes from
its library to the selected device, starting with the most popular code
5. To lock in the code, press and release SET.The LED will
blink twice.
6. To search for the codes of your other devices, repeat steps
1 through 5, but substitute the appropriate device key for
the device you are searching for. here is the maual for your remote:

Posted on Dec 12, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Get my garage door opener to lose from the remote?

I had a similar problem, but it ended up being the LED lightbulbs put in the opener to replace the incandescent--the LED bulbs were interfering with the remote signal somehow.
But while troubleshooting, I did learn to reset / reprogram the remote: press the Learn button on the opener, then press and hold the button on your remote. The opener lights should blink. That should reprogram your remote.
If that doesn't work, you might have to erase the codes from the opener memory, I think you need to press and hold the Learn button until the lights blink. But you might want to search how to do it for your specific unit.

Jan 09, 2015 | Remote Controls

1 Answer

Clicker garage door opener

I don't believe that you need to configure it.
It should be preconfigure to work.
What i think after revising the manual and from past experience with car remotes, the type of socket used for the battery inside the remote itself is often missing or broken solder. To make this more clear, the battery socket might need to be resolder on the small circuit board inside your remote.

good luck

Nov 29, 2013 | Viper Remote Controls

1 Answer

I got my centurion gate motor D3. the problem is when i press the remote an LED lights but the gate does not open, i opened the motor cover and there is no light nor sound from the motor. the gate can be...

Try to reprogram your remotes.... or replace the batteries even if the l.e.d. still works (it only takes half a volt to make the l.e.d. work but almost the full charge of the batteries are needed to send a working signal.

Oct 18, 2013 | Remote Controls

1 Answer

My chamberlaain security + garage door openers

well your main PC board inside of the opener head could have lost the frequency, or the unit memory has been erased, try to reprogram the remotes by going to the back of the opener head and locating the "learn" button which is either red, green, or purple in color. press the learn button then ONE button on ONE remote, pressing multiple buttons or pressing both remote buttons at the same time will not allow them to be programed successfully. after programing test by pushing the same button you just programmed, repeat for other remotes, and if this process did not work than you will need to contact chamberlain

Jan 17, 2010 | Chamberlain 950CB Remote Control

2 Answers

How to open remote control Sony RM-Y181

There should be small screws (usually phillips head) at either the top, bottom or both ends of the back of the remote. Unscrew those and pry loose. If not, they will be under the batteries, inside the battery cover.

I assume that's what you mean by open?


Aug 10, 2009 | Remote Controls

1 Answer

Changed code on the wireless chamberlain security key pad

Does it work from wall button? Hit learn button for 10 seconds. Hit again for 1 second and code keypad.Opener lights should blink 2x. Hit learn again for a second and hit button on a remote (Any button you chose). Again, lights should blink. Now should work. Repeat for any other remotes.

Jul 24, 2009 | Chamberlain 950CB Remote Control

6 Answers

I need a replacement remote control - Bose RC9

I have same problem with RC-9 working intermittently with some light banging. Thanks for the tip above. I tried opening the remote but the case wont open. Is there an easy way? Dont want to break the case while opening. Thanks.

Apr 07, 2009 | Remote Controls

1 Answer

Where to buy pre-1993 garage remote, or are the places to go to get this third opener. Thanks BB

Jan 13, 2009 | One For All URC-5705 Remote Control

Not finding what you are looking for?
One For All URC-3021 Remote Control Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top One For All Remote Controls Experts

The Knight
The Knight

Level 3 Expert

66413 Answers

Cindy Wells

Level 3 Expert

4719 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an One For All Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides